Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
Search Results "Vertical Alignment"
-
306.1 General
-
306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
Engineered vs. Outside
The seat values are of particular importance because vertical vibrations transferred through the seat of a seated individual are the most hazardous....
-
4.34.6.8* REFRIGERATOR/FREEZER
Provision shall be made for refrigerators which are: (1) Of the vertical side-by-side refrigerator/freezer type; or (2) Of the over-and-under type and meet the following requirements...
-
11B-1002.4.4 Clearances
Wheelchair spaces shall not be required to comply with Section 11B-307.4 _|Vertical Clearance|_. [2010 ADAS] Advisory 1002.4.4 Clearances Exception 3....
-
11B-303.3 Beveled
A change in level of ½ inch (13 mm) is permitted to be ¼ inch (6.4 mm) vertical plus ¼ inch (6.4 mm) beveled....
-
§ 38.159(b)(8) Platform entrance ramp
loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, measured on level ground, for a maximum rise of 3 inches (75 mm), and the transition from roadway or sidewalk to ramp may be vertical...
-
11B-806.2.3.1 Personal lift device floor space
The clear space shall extend to points horizontally 30 inches (762 mm), vertically 7 inches (178 mm) and not more than 12 inches (305 mm) from the head and foot end of the bed....
-
11B-806.2.3.1 Personal lift device floor space
The clear space shall extend to points horizontally 30 inches (762 mm), vertically 7 inches (178 mm) and not more than 12 inches (305 mm) from the head and foot end of the bed....
-
a. Structural Strength
The MDE NPRM proposed to require transfer supports to be capable of resisting vertical and horizontal forces of 250 pounds at all points (proposed M305.2.2)....
-
E102.5 IETF (Section-by-Section Analysis)
This proposed standard would be new to the 508 Standards (as well as the 255 Guidelines), and represents a significant shift to better align with current technology....
-
R305.2.1 Perpendicular Curb Ramps
The rows of truncated domes in detectable warning surfaces should be aligned perpendicular to the grade break between the ramp run and the street so pedestrians who use wheelchairs can ”...
-
R305 Detectable Warning Surfaces (Section-by-Section Analysis)
R305 Detectable Warning Surfaces (Section-by-Section Analysis) Detectable warning surfaces consist of truncated domes aligned in a square or radial grid pattern....
-
National Center for Mobility Management (NCMM)
e-newsletter, webinars, and conference calls Disseminate descriptions of relevant promising practices Collaborate with mobility management practitioners through several communication forums Align...
-
11B-306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
303.3 Beveled
A change in level of ½ inch (13 mm) is permitted to be ¼ inch (6.4 mm) vertical plus ¼ inch (6.4 mm) beveled....
-
206.3 Location
Additionally, accessible vertical interior circulation must be in the same area as stairs and escalators, not isolated in the back of the facility....
-
306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
11B-404.3.5 Controls
Where push plates, vertical actuation bars or other similar operating devices are provided, they shall be placed in a conspicuous location. ...
-
11B-602.9 Pedestrian protection
When used, wing walls or barriers shall project horizontally at least as far as the drinking fountain and to within 6 inches (152 mm) vertically from the floor or ground surface....
-
Raised and Braille Characters on Hoistway Entrances [4.10.5]
Recommendation:Since Braille characters can be difficult to read if placed too close to raised characters, consider a vertical clearance of at least 3/8 inch....
-
§ 38.83(b)(7) Platform gaps
floor height with the inner barrier (if applicable) down or retracted, gaps between the forward lift platform edge and vehicle floor shall not exceed 1/2 inch horizontally and 5/8 inch vertically...
-
11B-404.3.5 Controls
Where push plates, vertical actuation bars or other similar operating devices are provided, they shall be placed in a conspicuous location....
-
§ 38.23(b)(7) Platform gaps
floor height with the inner barrier (if applicable) down or retracted, gaps between the forward lift platform edge and the vehicle floor shall not exceed 1/2 inch horizontally and 5/8 inch vertically...
