Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
Search Results "Surface Material"
Filters
Commonly Searched Documents
-
11B-405.3 Cross slope
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel....
-
Pilot Rock TQ700 Square Frame Square Utility Table
Surface mount installation only (Anchor bolts not included - use Model ANC3-4 Anchor Kit). FINISH: All steel frame components have a powder coat finish in your choice of color....
-
Pilot Rock T700 Square Frame Rectangular Utility Table
Surface mount installation only (Anchor bolts not included - use Model ANC3-4 Anchor Kit). FINISH: All steel frame components have a powder coat finish in your choice of color....
-
GAP ARMOUR
GAP ARMOUR IS AN INNOVATIVE RUBBER MATERIAL ...that easily installs (with a rubber hammer) into open concrete expansion joints to completely seal and protect!...
-
Inpro Corporation JointMaster® 316 Series Single Sightline for Carpet Floor Expansion Joint Covers
The 316 series system was specially designed for continuous flooring types such as carpet and vinyl sheet. Features & Benefits System reduces joint widths of up to 4"...
-
7.2.2.1 Determining Impracticability
The surface is not firm and stable for a distance of 45 feet or more (14 m). Limiting Factor 3. ...
-
Seat Width Evaluation
many participants (the 25th through 95th percentiles) for their level, highest and lowest height transfer regardless of the presence or absence of grab bars or a backrest on the transfer surfaces...
-
Light Rail Platform Slope
The Board has explicitly specified that rail platforms shall slope no more than 1:48 in any direction, consistent with cross slope provisions for walking surfaces in section 403....
-
Executive Summary
After traveling over each surface, subjects were asked to subjectively rate each surface and decide whether the surface was acceptable or not....
-
Ytterberg Scientific Inc. FloorPro® Floor Flatness Measurement Device
It's Easier to Use, Gets Faster Results, and Produces Superior Reporting on More ASTM Specifications. FloorPro® Gives You Immediate Results, Instant F-Numbers, Waviness Index,...
-
Pilot Rock AT Series Traditional A-Frame Picnic Table With Steel Braces - Using Recycled Plastic
TOP/SEAT MATERIAL: 2” X 10” (nom.) 100% Recycled Plastic planks in your choice of color. See Material Options....
-
Pilot Rock Square Frame Square Table - Series TQ703
Surface mount installation only (Anchor bolts not included). Use Model ANC3-4 Anchor Kit. FINISH: All steel frame components have a powder coat finish in your choice of color....
-
Access Board: Accessible Route Carpet
This video is part of a longer animation produced by the U.S. Access Board. View the animation video in its entirety on the Access Board's website...
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible. ...
-
Non-Circular Cross Sections: ADA Standard Section 505.7.2
Section 505.7.2 covers the current ADA Standards for the non-circular cross section of handrail gripping surfaces.
-
11B-505.7.2 Non-circular cross sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible by Section 11B-226.1....
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible by Section 11B-226.1....
-
II. Research Methodology
Research Methodology The research design for this study of playground surfaces has been in development since 2005 with input from a national advisory committee. ...
-
Can stair treads and risers be perforated?
Stair treads must meet requirements for floor or ground surfaces which specify that surface openings not allow passage of a sphere more than ½ inch in diameter (§302.3)....
