5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302 Description: Transfer supports may contain elements to provide structural support or prevent...
Search Results "Pull Side"
Commonly Searched Documents
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
5.4.5 Transfer Support Position Recommendation for M301 and M302 Description: Transfer support position refers to the placement of the gripping surface within the minimum and...
-
5.4.2 Transfer Support Length for M301 and M302
5.4.2 Transfer Support Length for M301 and M302 Description: Transfer support length applies to the gripping surface of the support, that portion of the support used to grasp or...
-
5.7.1 Lift Compatibility Clearance in Base for M301
5.7.1 Lift Compatibility Clearance in Base for M301 Description: For portable floor lifts to be effective, they must deploy at diagnostic equipment such that the boom of the lifts...
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position.
-
Curb Ramp Requirements [§406]
Curb Ramp Requirements [§406]
- Brey-Krause Concealed Mounting Security / Anti Suicide Grab Bars
- Behavioral Safety Products #GB350 Suicide Resistant Safety Grab Bar with Full Closure Plate
-
Is compliance on both sides of a door or gate required when it is usable only from one side?
No, compliance is not required on both sides of those doors or gates that can be used in one direction only. Compliance is required only on the usable side....
-
Comparison of Single-User Toilet Room “Pairs” With Fixtures Side-by-Side: Plan 2C
Comparison of Single-User Toilet Room “Pairs” With Fixtures Side-by-Side: Plan 2C 2010 Standards Plan-2C Pair: 2010 Standards with In-Swinging Doors...
-
T208.2.2 Doorways on Two Sides of vehicle
Where non-rail vehicles have doorways on two sides, a passenger access route shall connect each wheelchair space to doorways on both sides of the vehicle that provide a means of accessible...
-
11B-404.2.4.1 Swinging doors and gates
Perpendicular to doorway Parallel to doorway (beyond latch side unless noted) From front Pull 60 inches (1524 mm) 18 inches (457...
-
DSA IR 16-12: GRAB BAR DESIGN AND CONNECTIONS: 2019 CBC
shall be established in the same manner. 2.3 As an alternate to Section 2.2 above for grab bars spanning 36” or less between supports, a connection using a back-up plate on the other side...
-
Bradley Center-Pull Towel Dispenser 2479 10 Side Elevation
Requires the Premium User plan or above. (Login or upgrade your account!)
-
11B-809.8.3 Door maneuvering clearance.
At the dwelling unit side of the primary entry doors, secondary exterior doors, and required exit doors maneuvering clearances shall be 44 inches (1118 mm) minimum in length measured...
-
M301.2.1 Adjustability
Transfer surfaces shall be adjustable in height measured from the floor to the top of the uncompressed transfer surface and shall provide the following: A. A low transfer position...
-
M301.2.2 Sunset
The low transfer position height, Item A of M301.2.1, shall cease to have effect on [Insert date 5 years after date of publication in the Federal Register].
-
M301.2.2 Sunset Provision (Section-by-Section Analysis)
As discussed in Section IV.B.1.a. (Significant Changes – Transfer Surface Adjustability), this is a new provision that was added to the final rule in conjunction with the new...
- The UpScale Medical Exam Table
- Stable and rock solid. See for yourself!
- Exam Tables & Scales: What Patients Say...
- Grohe Essence Kitchen Pull-out Faucet
-
Appendix 3 - Comparison of US Standards to IDEA Center Research
Reach 1270 119 1597 1347 1704 Low Side Reach 380...
-
M305.2.5 Surface Hazards
Transfer supports and surfaces adjacent to transfer supports shall be free of sharp or abrasive components and shall have eased edges.