1.2.1 Use the plus - or - minus symbol (±) after a dimension when it must be made clear what the expected tolerance is. This should be coordinated with the specification requirements....
Search Results "Children's Dimension"
Filters
Commonly Searched Documents
-
1.2.1
-
11B-407.4.7.2 Keypads
The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 11B-703.3.1 _|Braille Dimensions|_....
-
8.1 Excluded Populations Needing Future Attention
The numbers of children and youth under age 18 living with disabilities is growing and will continue rising in coming decades....
-
AssistiveWare Proloquo4Text Communication App
Proloquo4Text and have another app side-by-side on your screen (iOS 9) Ten new voices - Sharon (US English), Claudia (German), Kal & Mia (Swedish), Filip & Freja (Swedish children...
-
F216.12 Amusement Rides
Amusement rides designed primarily for children, amusement rides that are controlled or operated by the rider, and amusement rides without seats, are not required to provide wheelchair spaces...
-
216.12 Amusement Rides
Amusement rides designed primarily for children, amusement rides that are controlled or operated by the rider, and amusement rides without seats, are not required to provide wheelchair spaces...
-
B. Distribution of Funds
., number of persons receiving Aid to Families with Dependent Children or with limited English speaking ability] if the factor is included to compensate for past discrimination or to comply...
-
President’s Panel on Mental Retardation
Future administrations continue the effort, expanding its goals to include training in academic, vocational and social skills to enable children with intellectual disabilities to reach their...
-
Table of Contents
CHAPTER 1: APPLICATION AND ADMINISTRATION 101 Purpose 102 Dimensions for Adults and Children 103 Equivalent Facilitation 104 Conventions 105 Referenced Standards 106 Definitions...
-
608.2.1 Transfer Type Shower Compartments
Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
-
Urinal Depth
In the proposed rule, the Board sought to clarify the requirement in the original ADAAG that accessible urinals have an "elongated" rim by specifying a minimum dimension of 13 ½ inches,...
-
5.2.1.4 Transfer Surface Size for Imaging Equipment
The transfer surface should be located such that the long dimension of 28 inches is located parallel to the patient scanning/imaging side of the table....
-
407.12.3.1 Unobstructed Forward Reach (Section-by-Section Analysis)
These dimensions and their resulting geometry are consistent with the ADA and ABA Accessibility Guidelines (36 CFR Part 1191, Appendix D, sections 306 and 308)....
-
4.10.3 Hall Call Buttons
Call buttons shall be a minimum of 3/4 in (19 mm) in the smallest dimension. The button designating the up direction shall be on top. (See Fig. 20.) Buttons shall be raised or flush....
-
4.10.3 HALL CALL BUTTONS
Call buttons shall be a minimum of 3/4 in (19 mm) in the smallest dimension. The button designating the up direction shall be on top (see Fig. 20). Buttons shall be raised or flush....
-
Size and Clearances [4.21.2]
The 36 by 36 inch dimension, measured to the interior finish, keeps front and side grab bars within reach from the seat....
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
Wheelbase Definition
The larger of the dimensions measured on the right and left side of the mobility device were considered for the analysis....
-
Alterations [4.1.6(1)(f) & (k)]
Or, if an alteration involves replacing the cab but not the existing shaft, ADAAG recognizes that meeting the minimum car plan dimensions may not be technically feasible due to the existing...
-
Outdoor Constructed Features
The proposed rule based the size of the clear ground space at outdoor constructed features on the dimensions for clear floor or ground surfaces in 305.2 of the Architectural Barriers Act...
-
Wheelchair Spaces (M303.2)
This dimension is based on provisions in the 2004 ADA and ABA Accessibility Guidelines for maneuvering clearance where a clear floor or ground space is confined on all or part of three sides...
-
4.3.7 Clear Floor Space for Reaching
4.3.7 Clear Floor Space for Reaching Clear floor space dimensions for reaching are different than for seating because they require a specific orientation to the target....
-
1008.3 Transfer Systems
Moving between a transfer platform and a series of transfer steps requires extensive exertion for some children....
-
382.93 Must carriers offer preboarding to passengers with a disability?
., families with small children)....
