In transfer-type showers, the seat shall extend from the back wall to a point within 3 inches (75 mm) of the compartment entry....
Search Results "Transfer Surface Height"
-
610.3 Shower Compartment Seats
-
610.3 Shower Compartment Seats
In transfer-type showers, the seat shall extend from the back wall to a point within 3 inches (75 mm) of the compartment entry....
-
R302.7.2 Vertical Surface Discontinuities
R302.7.2 Vertical Surface Discontinuities. Vertical surface discontinuities shall be 13 mm (0.5 in) maximum....
-
Dispersion: ADA Standard Section 226.2
Section 226.2 covers scoping requirements in the current ADA Standards for dispersion of dining surfaces and work surfaces.
-
11B-1008.2.5.3.2 Handrail height
The top of handrail gripping surfaces shall be 20 inches (508 mm) minimum and 28 inches (711 mm) maximum above the ramp surface....
-
11B-1008.2.5.3.2 Handrail height
The top of handrail gripping surfaces shall be 20 inches (508 mm) minimum and 28 inches (711 mm) maximum above the ramp surface....
-
11B-1008.2.5.3.2 Handrail height
The top of handrail gripping surfaces shall be 20 inches (508 mm) minimum and 28 inches (711 mm) maximum above the ramp surface....
-
Surface discontinuities
Differences in level between two adjacent surfaces. Elevation changes due to ramps or stairs do not, themselves, constitute surface discontinuities....
-
Accessible Counter Height
Comments from the retail industry advised that a higher surface height is needed to accommodate various types of counters, such as glass display cases, which are typically manufactured at...
-
5.3.2.2 Surface
The surface of the turning space and clear floor or ground space shall be firm and stable....
-
1012.4 Surface
This section requires the surface of parking spaces and pull-up spaces to be firm and stable....
-
11B-605.2 Height and depth
11B-605.2 Height and depth. Urinals shall be the stall-type or the wall-hung type with the rim 17 inches (432 mm) maximum above the finish floor or ground....
-
R409.8 Surfaces
R409.8 Surfaces. Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
5.4.9 Interruptions Along Transfer Support Gripping for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.9 Interruptions Along Transfer Support Gripping for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
11B-605.2 Height and depth
FIGURE 11B-605.2 HEIGHT AND DEPTH OF URINALS...
-
Figure 1009.5.2 Clear Deck Space at Transfer Platform – Drawing from the U.S. Access Board
-
T402.5 Surfaces
Ramp and bridgeplate surface material shall comply with T302 and extend across the full width and length of the ramp or bridgeplate....
-
11B-810.2.1 Surface
Bus stop boarding and alighting areas shall have a firm, stable surface....
-
11B-810.2.1 Surface
Bus stop boarding and alighting areas shall have a firm, stable surface....
-
11B-810.2.1 Surface
Bus stop boarding and alighting areas shall have a firm, stable surface....
-
Unitary Surface
Unitary Surfaces. The predominant surface characteristic is whole. ...
-
Technical Memorandum TM 2017-25 Door and Gate Surfaces
floor to have a smooth surface on the push side....
-
4.2.7 Surface
The surface of the clear floor or ground space shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
226 Dining Surfaces and Work Surfaces
226 Dining Surfaces and Work Surfaces...
