This procedure was repeated until the largest horizontal distance was reached. The maximum and minimum heights attainable with the largest horizontal distance were recorded. ...
Search Results "Horizontal Standing Support"
-
Adjustable height/gap protocol
-
2. Neighborhood Access
As support for her position, Kirola relies principally on Chapman v. Pier 1 Imports (U.S.) Inc., 631 F.3d 939, 943 (9th Cir. 2011) (en banc) ("Chapman I")....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
Door and Gate Surfaces: ADA Standard Section 404.2.10
Section 404.2.10 covers the current ADA Standards for door and gate surfaces on manual doors and gates.
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
11B-201.3 Temporary and permanent structures
Temporary buildings or facilities covered by these requirements include, but are not limited to, reviewing stands, temporary classrooms, bleacher areas, stages, platforms and daises, fixed...
-
11B-201.3 Temporary and permanent structures
Temporary buildings or facilities covered by these requirements include, but are not limited to, reviewing stands, temporary classrooms, bleacher areas, stages, platforms and daises, fixed...
-
11B-703.8.4 Character height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
11B-703.8.4 Character height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
Building
Any structure used or intended for supporting or sheltering any use or occupancy....
-
Weight Scales
The scales are grouped by the following types: stand-on scales and wheelchair scales. Within each group, there are mechanical and digital scales....
-
5.3.1 Permitted Obstructions to Transfer Sides for M301 and M302
NPRM Preamble Discussion: The Access Board is considering whether the final standards should permit equipment parts to extend horizontally 3 inches maximum beyond the edge of the transfer...
-
ASI Storage Solutions Phenolic Lockers
These lockers are fabricated to stand the test of time....
-
TREAD
The horizontal part of a step....
-
Clear Floor Space: Minimum Clear Floor Space Required for Forward and Side Approach - Manual Wheelchair
These dimensions are: (A) occupied width, the horizontal distance between the side-most (lateral-most) points of the wheelchair or occupant on the right and left side; (B) occupied length...
-
Clear Floor Space: Minimum Clear Floor Space Required for Forward and Side Approach - Scooter
These dimensions are: (A) occupied width, the horizontal distance between the side-most (lateral-most) points of the wheelchair or occupant on the right and left side; (B) occupied length...
-
Clear Floor Space: Minimum Clear Floor Space Required for Forward and Side Approach - Power Chair
These dimensions are: (A) occupied width, the horizontal distance between the side-most (lateral-most) points of the wheelchair or occupant on the right and left side; (B) occupied length...
-
11B-806.2.3.1 Personal lift device floor space
The clear space shall extend to points horizontally 30 inches (762 mm), vertically 7 inches (178 mm) and not more than 12 inches (305 mm) from the head and foot end of the bed....
-
TREAD
The horizontal part of a step....
-
11B-703.5.10 Format
Text shall be in a horizontal format....
-
11B-703.2.9 Format
Text shall be in a horizontal format....
-
11B-703.5.10 Format
Text shall be in a horizontal format....
