Adaptability means the ability of certain elements of a dwelling unit, such as kitchen counters, sinks, and grab bars, to be added to, raised, lowered, or otherwise altered, to accommodate...
Search Results "Counter Length"
Filters
Commonly Searched Documents
-
§8.3 Adaptability
-
III-7.8200 Restaurants and cafeterias
ADAAG contains requirements for counters and bars, access aisles, food service lines, tableware and condiment areas, raised speaker's platforms, and vending machine areas (but not controls...
-
5.4.9 Interruptions Along Transfer Support Gripping for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
The bottom of the transfer support shall have no obstruction affecting more than 20% of its length....
-
R409.3 Continuity
Handrails shall be continuous within the full length of each ramp run or stair flight....
-
Can guards or collars be attached to handrails to prevent skateboard traffic?
surfaces at egress stairs subject to the Standards must be unobstructed on the top and sides and free of sharp or abrasive elements so that users can maintain a continuous grip along the full length...
-
E1-a
Is there an accessible route, at least 36 inches wide, that connects the accessible entrance to all shelter areas (it may narrow to 32 inches wide for up to 2 feet in length)?...
-
§ 37.131(c)(1)
(1) In calculating the full fare that would be paid by an individual using the fixed route system, the entity may include transfer and premium charges applicable to a trip of similar length...
-
M303.2.3 Wheelchair Spaces / Depth of Wheelchair Spaces for front or Rear Entry
• Sub-Committee Recommendation: Platform size shall be clear width of 32 inches minimum and clear length of 40 inches minimum....
-
Step 3: Apply the Accessibility Provisions
If the grade requirement can't be met because of a condition for an exception, measure and record the length of trail that will deviate from the technical requirement....
-
1.1.13 Flatness of ramp running slope
Measure flatness in the running slope of ramps at 12 - in. (300 mm) increments by using successive, overlapping 24 - in. (600 mm) lengths using a 24 - in. digital inclinometer....
-
Gift Shops
Hand credit cards back to your guest, rather than leaving them on a counter....
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
This provision would apply along the support length and not to the cross-sectional profile of the gripping surface, see Figure 5.4.1.1....
-
Ramp
The minimum length was 8 inches and the maximum length was 11 inches....
-
11B-607.2 Clearance
Clearance in front of bathtubs shall extend the length of the bathtub and shall be 48 inches (1219 mm) wide minimum for forward approach and 30 inches (762 mm) wide minimum for parallel...
-
11B-810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2438 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
§ 38.23(d)(4) Orientation
In vehicles in excess of 22 feet in length, at least one securement device or system required by paragraph (a) of this section shall secure the wheelchair or mobility aid facing toward the...
-
11B-607.2 Clearance
Clearance in front of bathtubs shall extend the length of the bathtub and shall be 48 inches (1219 mm) wide minimum for forward approach and 30 inches (762 mm) wide minimum for parallel...
-
11B-810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2438 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
Kompan, Inc. M243 - Crocodile Bench
Small builders will gather and explore loose materials on the counters....
-
Dining Surface and Work Surface
Some commenters considered the term too limiting and questioned whether it would apply, as they felt it should, to surfaces used forpurposes not necessarily considered "work," such as counters...
-
4.16.4 Grab Bars
Among the various specifications for grab bars in general, including diameter, spacing, and structural strength (ADAAG 4.26) and for toilets in particular, including length and positioning...
-
M305.3.2 Vertical Position
Where the support is vertical, it shall be 18 inches (455 mm) minimum in length and the bottom end of the support shall be 34 inches (865 mm) high minimum and 37 inches (940 mm) high maximum...
-
A. Door Width
on an over-the-road bus is considered not feasible if doing so would necessitate reduction of the bus approach angle, relocating the front axle rearward, or increasing the bus overall length...
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
