(c) A grab bar at least 24 inches (610 mm) long should be mounted behind the water closet, and a horizontal grab bar at least 40 inches (1015 mm) long should be mounted on at least one side...
Search Results "Rear Grab Bar"
Filters
Commonly Searched Documents
-
(1)(c)
-
11B-604.9.4 Grab bars
Grab bars for water closets shall comply with Section 11B-604.5....
-
Grab Bars
The most common location for grab bars is in restrooms....
-
11B-607.4.2.1 Back wall
Two grab bars shall be installed on the back wall, one located in accordance with Section 11B-609.4 and the other located 8 inches (203 mm) minimum and 10 inches (254 mm) maximum above the...
-
Non-Circular Cross Section: ADA Standard Section 609.2.2
Section 609.2.2 covers the current ADA Standards for non-circular grab bar cross sections.
-
1607A.9.2 Grab bars, shower seats and accessible benches
Grab bars, shower seats and accessible benches shall be designed to resist a single concentrated load of 250 pounds (1.11 kN) applied in any direction at any point on the grab bar, shower...
-
Control End Wall: ADA Standard Section 607.4.2.2
Section 607.4.2.2 covers the current ADA Standards for grab bars on the control end of bathtubs without permanent seats.
-
Control End Wall: ADA Standard Section 607.4.1.2
Section 607.4.1.2 covers the current ADA Standards for grab bars on the control end of bathtubs with permanent seats.
-
Head End Wall: ADA Standard Section 607.4.2.3
Section 607.4.2.3 covers the current ADA Standards for grab bars on the head end wall of bathtubs without permanent seats.
-
Grab Bars
Specifications for grab bars are addressed in section 604.5. Grab bars are required on one side wall and the rear wall....
-
Surface Hazards: ADA Standard Section 609.5
Section 609.5 covers the current ADA Standards for the surfaces of grab bars and adjacent surfaces.
-
AJW Architectural Products US130-A Series US130-A12 12" Exposed Flange, 1.5" Diameter Security Grab Bar - Configuration A
Grab bars must be installed properly to support the loads intended....
-
DSA IR 16-12: GRAB BAR DESIGN AND CONNECTIONS: 2019 CBC
DESIGN REQUIREMENT: Grab bars shall be designed to resist a single concentrated load of 250 LBS applied in any direction at any point on the grab bar such as to produce the maximum load...
-
AJW Architectural Products UG130-A Series UG130-A12 12" Exposed Flange, 1.5" Diameter Grab Bar - Configuration A
Installation: Before installing grab bars, verify with all state and local codes for requirements on bar diameter and type finish....
-
AJW Architectural Products UG120-A Series UG120-A12 12" Exposed Flange, 1.25" Diameter Grab Bar - Configuration A
Installation: Before installing grab bars, verify with all state and local codes for requirements on bar diameter and type finish....
-
Murdock Manufacturing Grab Bars
Grab bar is 1-1/2 inch (3.81 cm) diameter satin finish stainless steel and have 1-1/2 inch (3.81 cm) clearance to wall....
-
AJW Architectural Products UG3-A Series UG3-A12 12" Concealed Snap Flange, 1.5" Diameter Grab Bar - Configuration A
Bars with greater offsets will support loads up to 250lbs when properly installed....
-
AJW Architectural Products UG2-A Series UG2-A12 12" Concealed Snap Flange, 1.25" Diameter Grab Bar - Configuration A
Bars with greater offsets will support loads up to 250lbs when properly installed....
-
AJW Architectural Products UG30-A Series UG30-A12 12" Concealed Set Screw Flange, 1.5" Diameter Grab Bar - Configuration A
Flanges are heliarc welded to bar to form a one piece construction....
-
AJW Architectural Products UG20-A Series UG20-A12 12" Concealed Set Screw Flange, 1.25" Diameter Grab Bar - Configuration A
Flanges are heliarc welded to bar to form a one piece construction....
-
Moen Home Care Glacier 12" Grab Bar
complies with Americans with Disabilities Act (ADA) specifications 12" bar length 1.5" bar diameter corrosion resistant stainless steel construction for added durability limited...
-
Moen Home Care Peened 12" Grab Bar
complies with Americans with Disabilities Act (ADA) specifications 12" bar length 1.5" bar diameter corrosion resistant stainless steel construction for added durability limited...
-
Structural Strength: ADA Standard Section 609.8
Section 609.8 covers the current ADA Standards for the structural strength of grab bars.
-
Just Manufacturing 24" Stainless Steel Grab Bar
Type 304, 18 Gauge Stainless Steel. 24" Length x 1-1/2" Diameter with concealed screws Brushed stainless finish Grab bar to wall distance 1-1/2" ADA Compliant...
