Lav Shield® provides ADA-compliant undersink protection and meets requirements for wheelchair accessibility. Durable, single-piece construction conceals piping, electronic faucet...
Search Results "Vertical Clearance"
Filters
Commonly Searched Documents
-
IPS Corporation Truebro® Lav Shield® Protective Lavatory Enclosure
-
McGuire Manufacturing Co., Inc. PW1000WC: 1 1/2" Offset Sink
1 1/2" offset sink assembly prewrapped.
-
McGuire Manufacturing Co., Inc. 1000WC: Offset Strainer - Offset Only
Offset sink strainer wheelchair offset. Allows up to 11" offset for wheelchair access use of most ADA sinks. The offset fits most 1 1/2" direct connect sink strainers including all...
-
McGuire Manufacturing Co., Inc. 1152WC: Offset with 152 Wide Top Strainer
Offset sink strainer with chrome plated wrought brass 4 1/2" wide top sink strainer. 1 3/4" x 4 1/2" OD.
-
McGuire Manufacturing Co., Inc. Heavy Finish Offset Lavatory Strainer
Classic McGuire wheelchair lavatory strainer. Furnished with heavy cast brass grid drain strainer, elbow and 1 1/4" 17GA seamless tubular offset tailpiece. PVD chrome finish. ADA...
-
Voting Area
Within the voting area there must be enough clearance for an individual with a disability to access and use all the voting equipment....
-
Re: 404.2.4.3 Recessed Doors and Gates
Notice that the text does not match the figure for a push approach door. This may be an error in the Standards, but since the text governs, it exceeds the illustrated requirement. ...
-
4.17.5* DOORS
If toilet stall approach is from the latch side of the stall door, clearance between the door side of the stall and any obstruction may be reduced to a minimum of 42 in (1065 mm)....
-
Access Board: Accessible Van Parking
This video is part of a longer animation produced by the U.S. Access Board. View the animation video in it's entirety on the Access Board's website here:...
-
4.17.5* Doors
If toilet stall approach is from the latch side of the stall door, clearance between the door side of the stall and any obstruction may be reduced to a minimum of 42 in (1065 mm) (Fig. 30...
-
11B-404.2.4.1 Swinging doors and gates
TABLE 11B-404.2.4.1 MANEUVERING CLEARANCES AT MANUAL SWINGING DOORS AND GATES TYPE OF USE MINIMUM MANEUVERING CLEARANCE Approach...
-
Wikk Industries Inc. Bollard With Push Plate PART#BPRT126SMFT32D (630)
12”x6”x42” Tall, 7ga. Formed 304 Satin Stainless Steel US32D (630), Surface mount with concealed mounting base, 1 prep for INGRESS’R ® ADA switch (630), Welded Flat top. Shown on...
-
SDC Bollard Post with Push Plate or Touch Panel
Alternative to wall mounted access control or switches for entry doors. Bollard post provide visibility and meet accessibility guidelines. Practical solution for surface mount or...
-
Wikk Industries Inc. PART#BPS SM-INGR CLEAR (628) with I36-3 CLEAR (628)
6”X6”X42” Tall, Clear Anodized Aluminum (628), Surface mount with concealed mounting base, 1 prep for INGRESS’R® ADA switch, Removable Black ABS cap Shown on the bollard- I36-3...
-
Wikk Industries Ingress'r Automatic Door Control
FEATURES: Weather resistant design allows interior or exterior application without adaptation UL® 15 amp. micro switch Crafted in clear anodized aluminum - will quote...
-
Wikk Industries Inc. PART# BPS SM-ING48 DB (710) with I36-3 Clear (628)
6”X6”X48” Tall, Dark Bronze Anodized Aluminum (710), Surface mount with concealed mounting base, 2 Preps for INGRESS’R® and card reader, Removable Black ABS Cap. **Customer can...
-
BEA Inc. LPR36 Series 36" Low Profile Push Plate
The LPR36 maximizes accessibility and independence for people with disabilities. The entire surface is “all-active” with four redundant membrane switches for consistent coverage. The...
-
11B-809.10.4 Sufficient maneuvering space
The clear maneuvering space shall be permitted to include knee and toe clearance under bathroom fixtures....
-
1132A.4 Level floor or landing
1132A.4 Level floor or landing. See also Chapter 10. The floor or landing on each side of a door shall be level. Primary entry doors, required exit doors or secondary exterior doors...
-
8. Gap
8. Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so...
-
11. Gap
11. Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so...
