The Midmark 641 Barrier-Free® power procedures chair offers versatile positioning, increased accessibility and better patient comfort to help meet these changing demands, allowing you to...
Search Results "Baby Changing Table"
Filters
Commonly Searched Documents
-
Midmark 641 Barrier-Free® Power Procedures Chair
-
6.9 Tread Obstacles
Obstacles on beach access routes and their related resting intervals shall not exceed 1 inch (25 mm) in height measured vertically to the highest point. Where the surface is...
-
§ 38.125(b)(8) Platform entrance ramp
(8) Platform entrance ramp. The entrance ramp, or loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, when measured on level ground, for a maximum rise of 3 inches,...
-
11B-502.4 Floor or ground surfaces
Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved. Advisory 11B-502.4 Floor or ground surfaces....
-
M305.2.2 Length
The length of transfer supports shall comply with M305.2.2.1 or M305.2.2.2.
-
M301.2.1 Height
The height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured from the floor to the top of the transfer...
-
Final Regulatory Impact Analysis
See Final RIA, table ES–1 & figure ES–2....
-
5.1.4 Transfer Surface Height Measurement for M301 and M302
This recommendation applies to exam tables and chairs and this measurement may not necessarily be at the centerline of the seat where there are higher points on the seat....
-
(2) Adjustability: Minimum Low Transfer Height
Specifically, the imaging equipment manufacturers asserted that: given the integrated nature of the table to the system and its imaging performance, that a change of even a few...
-
Food and Restaurant Services
In a dining area, remember to arrange tables far enough apart so a person using a wheelchair can maneuver between the tables when patrons are sitting at them....
-
Hybrid Surface Systems
After 12 months of installation, the top layer carpet began to shrink and separate at the seams creating openings and changes in level greater than ½ inch. ...
-
ALTERATION
[DSA-AC] A change, addition or modification in construction, a change in occupancy or use, or structural repair to an existing building or facility....
-
PEMKO 1 3/4" Carpet Separator Threshold No. 236
Requires the Premium User plan or above. (Login or upgrade your account!) -
PEMKO 2 1/2" Carpet Separator Threshold No. 174
Requires the Premium User plan or above. (Login or upgrade your account!) -
PEMKO 1 3/8" Carpet Separator Threshold No. 1951
Requires the Premium User plan or above. (Login or upgrade your account!) -
(4) Adjustability: Method of Measurement
The MDE NPRM proposed that the measurement of the height of the transfer surface for both diagnostic equipment used in the supine, prone, or side-lying position and diagnostic...
-
503.4 Floor and Ground Surfaces
Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
M305.2.8 Fittings
Transfer supports shall not rotate within their fittings when in place for transfer.
-
M305.2.7 Clearance
Clearance between the transfer support gripping surface and adjacent surfaces or obstructions shall be 1 ½ inches (38 mm) minimum.
-
M305.2.7 Clearance (Section-by-Section Analysis)
In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support. However, in the preamble to the MDE NPRM the Access Board...
-
5.4.10 Transfer Support Fittings Recommendations for M301 and M302
5.4.10 Transfer Support Fittings Recommendations for M301 and M302 Description: To ensure safe and effective transfers, transfer supports must not rotate within their fittings...
-
5.4.10 Transfer Support Fittings for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.10 Transfer Support Fittings for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position. The transfer supports shall not rotate when locked in place for patient...
-
Height – M301.2.1 & M302.2.1
Height – M301.2.1 & M302.2.1 The subcommittee discussed the increments for adjustability and decided that infinite adjustability is the appropriate standard as both electronic...
-
M305.2.3 Fittings
Transfer supports shall not rotate within their fittings.
