(3) Ramp threshold. The transition from station platform to the ramp or bridge plate and the transition from car floor to the ramp or bridge plate may be vertical without edge...
Search Results "Support Rail"
Filters
Commonly Searched Documents
-
§ 38.125(c)(3) Ramp threshold
-
§ 38.83(b)(8) Platform entrance ramp
(8) Platform entrance ramp. The entrance ramp, or loading-edge barrier used as a ramp, shall not exceed a slope of 1:8 measured on level ground, for a maximum rise of 3 inches, and...
-
§ 38.95(c)(2) Ramp surface
(2) Ramp surface. The ramp or bridge plate surface shall be continuous and slip resistant, shall not have protrusions from the surface greater than 1/4 inch high, shall have a clear...
-
§ 38.125(c)(6)(i) Requirement
(i) Requirement. When in use for boarding or alighting, the ramp or bridge plate shall be attached to the vehicle, or otherwise prevented from moving such that it is not subject to...
-
§ 38.95(d) Mobility aid seating location
(d) Mobility aid seating location. Spaces for persons who wish to remain in their wheelchairs or mobility aids shall have a minimum clear floor space 48 inches by 30 inches. Such...
-
§ 38.95(a)(2) Exception
(2) Exception. If level-entry boarding, portable or platform lifts, ramps or bridge plates meeting the applicable requirements of this section are provided on station platforms or...
-
§ 38.95(c)(3) Ramp threshold
(3) Ramp threshold. The transition from station platform to the ramp or bridge plate and the transition from car floor to the ramp or bridge plate may be vertical without edge...
-
§ 38.93(d)(3) Exception
(3) Exception. Where platform set-backs do not allow the horizontal gap or vertical alignment specified in paragraph (d)(1) or (d)(2) of this section, car, platform or portable lifts...
-
5.4.7 Transfer Support Gripping Surface Clearance for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.7 Transfer Support Gripping Surface Clearance for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302 Description: Gripping surface hazards are sharp or abrasive elements that prevent an individual from sufficiently...
-
5.4.3 Transfer Support Height for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.3 Transfer Support Height for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Americans with Disabilities Act (ADA) Standards for Transportation Facilities
DOT’s ADA Standards apply to facilities used by state and local governments to provide designated public transportation services, including bus stops and stations, and rail stations....
-
T704 Announcement Systems
Stop request systems must provide audible and visible notification onboard the non-rail vehicle indicating that a passenger has requested to disembark at the next stop. See T704.3....
-
T202 Accessible Means of Boarding and Alighting
All buses, OTRBs, and vans covered under the 2016 Non-Rail Vehicle Guidelines must provide at least one means of accessible boarding and alighting that serves all designated stops on the...
-
5.4.4 Transfer Support Distance From Transfer Surface for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.4 Transfer Support Distance From Transfer Surface for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Detectable Warnings [§406.8 (DOT’s Standards), §705]
are required on curb ramps at transit facilities covered by DOT’s Standards (facilities used by state and local governments to provide designated public transportation services, such as rail...
-
Requirements to Remember for ADA Compliance in Construction Projects: Transportation Facilities
the Department of Transportation (DOT) apply to facilities used by state and local governments to provide designated public transportation services, including bus stops and stations, and rail...
-
11B-206.4.4.1 Location
Exception: Entrances to key stations and existing intercity rail stations retrofitted in accordance with 49 CFR 37.49 or 49 CFR 37.51 shall not be required to comply with Section 11B-206.4.4.1...
-
11B-206.4.4.1 Location
Exception: Entrances to key stations and existing intercity rail stations retrofitted in accordance with 49 CFR 37.49 or 49 CFR 37.51 shall not be required to comply with Section 11B-206.4.4.1...
-
M305.2.8 Fittings (Section-by-Section Analysis)
Further, this commenter noted that the requirement conflicts with proposed M302.2.3, which allows for temporary obstructions such as armrests, footrests, and side rails that can be repositioned...
-
Project LETS (Let's Erase the Stigma)
We establish peer-led communities of advocacy & support; produce resources and educational materials; and aim to protect the civil and human rights of mentally ill folks through policy...
-
A Complete Guide to Service, Therapy and Emotional Support Dogs
A Complete Guide to Service, Therapy and Emotional Support Dogs Have you ever thought about getting a service dog to help you or a loved one? ...
-
Transfer Protocols
For each transfer, participants were asked to position themselves next to the platform as they normally would to prepare for a transfer. The angle of their WMD relative to the front...
-
§ 38.107(a)(1)
(1) The minimum clear floor area shall be 35 inches by 60 inches. Permanently installed fixtures may overlap this area a maximum of 6 inches, if the lowest portion of the fixture is...
