EXCEPTION: Within employee work areas, the required clear width of ramps that are a part of common use circulation paths shall be permitted to be decreased by work area equipment provided...
Search Results "Kitchen Work Surface"
Filters
Commonly Searched Documents
-
405.5 Clear Width
-
305.2 Floor or Ground Surfaces
Floor or ground surfaces of a clear floor or ground space shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
305.2 Floor or Ground Surfaces
Floor or ground surfaces of a clear floor or ground space shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
11B-1005.3.2 Extended ground or deck surface
The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing....
-
305.2 Floor or Ground Surfaces
Floor or ground surfaces of a clear floor or ground space shall comply with 302. Changes in level are not permitted....
-
609.5 Surface Hazards
609.5 Surface Hazards. Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....
-
505.6 Gripping Surface
The bottoms of handrail gripping surfaces shall not be obstructed for more than 20 percent of their length....
-
505.6 Gripping Surface
Where handrails are provided along walking surfaces with slopes not steeper than 1:20, the bottoms of handrail gripping surfaces shall be permitted to be obstructed along their entire length...
-
505.6 Gripping Surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
a. Transfer Surface Adjustability
The MDE NPRM proposed that the same transfer surface height range of 17 inches minimum to 19 inches maximum be applied to both diagnostic equipment used in the supine, prone, or side-lying...
-
Handrail Gripping Surfaces: ADA Standard Section 1008.2.5.3.1
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
Technical Bulletin: Ground and Floor Surfaces
UNITED STATES ACCESS BOARD A FEDERAL AGENCY COMMITTED TO ACCESSIBLE DESIGN Technical Bulletin: Ground and Floor Surfaces...
-
Door and Gate Surfaces [§404.2.10]
Door and Gate Surfaces [§404.2.10] The bottom surface of doors and gates on the push side must be smooth to a height of at least 10”....
-
Rotational Penetrometer Measurements of Firmness and Stability
The results of the Rotational Penetrometer correlated with those of the Wheelchair Work Measurement Method....
-
11B-404.2.4.4 Floor or ground surface
Floor or ground surface within required maneuvering clearances shall comply with Section 11B-302....
-
Delta How to Install a Pull-Out Faucet Featuring Touch20® Technology
With proper installation, your pull-out kitchen faucet with Touch20® Technology will bring years of stylish, efficient water delivery....
-
American Standard Cadet 2-Handle High-Arc Bar Sink Faucet 2475F
This two-handle, centerset bar sink faucet belongs to our Cadet® Kitchen Suite and complements casual décor....
-
Firmness, Stability, and Slip Resistance [§302.1]
Firmness, Stability, and Slip Resistance [§302.1] Accessible floor and ground surfaces must be stable, firm, and slip resistant....
-
IV. Discussion of Findings and Implications
of surface maintenance to assure accessibility and safety for use by children on a daily basis. ...
-
General [4.5.1]
Design guidelines cannot encompass all criteria contributing to the safety of a walking surface....
-
410.2 Floor Surfaces
Floor surfaces in platform lifts shall comply with 302 and 303....
-
410.2 Floor Surfaces
Floor surfaces in platform lifts shall comply with 302 and 303....
-
22. Must an employer allow an employee with a disability to work a modified or part-time schedule as a reasonable accommodation, absent undue hardship?
If modifying an employee's schedule poses an undue hardship, an employer must consider reassignment to a vacant position that would enable the employee to work during the hours requested...
-
R408.4 Tread Surface
R408.4 Tread Surface. Stairway treads shall comply with R302.7. Changes in level are not permitted....
