Assembly areas In the NPRM, the Department proposed Sec. 35.151(g) to supplement the assembly area requirements of the 2004 ADAAG, which the Department is adopting as part of the 2010 Standards...
Search Results "ANSI/IEEE: American National Standards Institute/ Institute of Electrical and Electronics Engineers"
Filters
Commonly Searched Documents
-
Section 35.151(g) Assembly areas
-
Accessible Jury Boxes, Attorney Areas, and Witness Stands
Section 206.2.4 of the 2010 Standards requires, in new construction and alterations, at least one accessible route to connect accessible building or facility entrances with all accessible...
-
707 Automatic Teller Machines and Fare Machines
Federal procurement law requires that ITMs purchased by the Federal government comply with standards issued by the Access Board under Section 508 of the Rehabilitation Act of 1973, as amended...
-
409 Private Residence Elevators
Residential dwelling units may be equipped with either a LULA elevator or a private residential elevator instead of a standard passenger elevator (206.6)....
-
LULA Elevators in Residential Dwelling Units
Residential dwelling units may be equipped with either a LULA elevator or a private residential elevator instead of a standard passenger elevator (206.6)....
-
407.1 General
Elevators shall comply with 407 and with ASME A17.1 (incorporated by reference, see "Referenced Standards" in Chapter 1). They shall be passenger elevators as classified by ASME A17.1....
-
11B-703.3 Braille
Standard English uses contractions like "don't" as a short way of writing two words, such as "do" and "not." In Braille there are many additional contractions. ...
-
M101.4 Equivalent Facilitation (Section-by-Section Analysis)
permit the use of alternative designs or technologies that are substantially equivalent to or provide greater accessibility and usability than strict compliance with provisions in the MDE Standards...
-
Is Identification of Which Means of Egress Are Available/Closest Necessary?
Once notified, people with a speech disability can use any standard means of egress from the building....
-
HOW TO MEASURE TRANSFER HEIGHTS IS IMPORTANT
Because of these complex shapes, it is necessary to create a standard method by which to measure table seat dimensions....
-
407.1 General
Elevators shall comply with 407 and with ASME A17.1 (incorporated by reference, see "Referenced Standards" in Chapter 1). They shall be passenger elevators as classified by ASME A17.1....
-
Technical Memorandum TM 2012-08 Private Clubs
TM 2012-08 Private Clubs Effective Date: January 22, 2013 2012 TAS Reference: 201.1 In accordance with TAS 201.1, the requirements of the Texas Accessibility Standards are...
-
707 Automatic Teller Machines and Fare Machines
Federal procurement law requires that ITMs purchased by the Federal government comply with standards issued by the Access Board under Section 508 of the Rehabilitation Act of 1973, as amended...
-
5.2.1 Transfer Surface Size Recommendations for M301
The transfer surface size standard has two components: width and depth (see Figure 5.2.1.1) NPRM Proposed Provision: M301.2.2 Size....
-
5.2.3 Transfer Surface Measurement Recommendation for M301 and M302
5.2.3 Transfer Surface Measurement Recommendation for M301 and M302 Description: The transfer surface size standard has two components: width and depth....
-
Elevators
In newly constructed or altered facilities, elevators must comply with specific design standards regarding the following: Hall call button orientation, mounting location, and visual...
-
Maximum Extent Feasible
maximum extent feasible," as used in this code, applies to the case where the nature of an existing facility makes it virtually impossible to comply fully with applicable accessibility standards...
-
410.7 Caller ID (Section-by-Section Analysis)
This requirement would be new to the 255 Guidelines, but corresponds to a similar requirement in § 1194.23(e) of the existing 508 Standards....
-
C101.1 Purpose (Section-by-Section Analysis)
exclusive authority to enforce Section 255 and issue implementing regulations; the FCC may—but is not required to—adopt the proposed guidelines when finalized as enforceable accessibility standards...
-
Create an Emergency Plan for Your Home
People are more likely to die in a fire at home than at work, and that risk is even greater for people with disabilities, said Brian Black, director of building codes and standards for Eastern...
-
Trail Classes
They are based on forest plan direction and represent intended design and management standards....
-
410.5 Digital Encoding of Speech
EXCEPTION: Where ICT is a closed system, conformance to standards other than ITU-T Recommendation G.722 shall be permitted where equivalent or better acoustic performance is provided and...
-
103 Equivalent Facilitation
ETA Editor's Note Although the wording of this section is the same as the 2010 ADA Standards, this provision is not the same for Texas and the ADA because Texas requires prior approval...
-
106.5.60 Shopping Center or Shopping Mall
For purposes of this standard, places of public accommodation of the types listed in the definition of "place of public accommodation" in Chapter 68, Texas Administrative Code are considered...