TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...
Search Results "Mitigating Measures"
-
11B-703.3.1 Dimensions and capitalization
-
ASSESSMENT, PROGRESS, ACHIEVEMENT, AND GRADING
Assessment instruments that compare the individual against herself or himself are able to measure both attainment and growth....
-
III-4.4300 Standards to apply
Measures taken to remove barriers should comply with the ADA Accessibility Guidelines (ADAAG) contained in the appendix to the Department's rule....
-
Standardized Tests of Physical Fitness and Community Ambulation
Resting heart rate and energy consumption were measured with the subject seated or reclining on a couch. Heart rate was measured with a Polar heart rate monitor (Polar Vantage XL)....
-
What values are recommended for ground and floor surfaces along an accessible route?
In the study sponsored by the Access Board, laboratory measurements from a Kistler force plate and computer analysis of the gaits of persons with mobility impairments (including crutch users...
-
Capabilities, Resources, and Facilities
hands-on experience with the measurement of all classes of anthropometric dimensions. hands-on experience with experimental subjects and human use considerations....
-
4.5 Weight Scales
In certain circumstances, such as setting chemotherapy dosages, weight is often a critical measurement....
-
Test Procedures
Accessibility Measures All surfaces were measured with the rotational penetrometer periodically over the first 6 months of exposure (Fig. 9)....
-
B. Technical standards for criterion-related validity studies
The possibility of bias should be considered both in selection of the criterion measures and their application....
-
1133A.2.1 Clear width
Kitchens shall have a minimum clear width measured between any cabinet, countertop or the face of any appliance (excluding handles and controls) that projects into the kitchen and the opposing...
-
604.9.3 Height
The height of water closets shall be 11 inches (280 mm) minimum and 17 inches (430 mm) maximum measured to the top of the seat....
-
M302.2.3 Size
The size of transfer surfaces shall be measured from center points of their opposing sides....
-
T402.8.1 Deployment to Roadways or to Curb Height Boarding and Alighting Areas
The running slope of ramps and bridgeplates used for deployment to the roadway or to curb-height boarding and alighting areas shall be 1:6 maximum, as measured to ground level with the non-rail...
-
§ 36.304(d)(4) Exemption for small facilities
For measures taken to comply with the barrier removal requirements of this section, existing facilities shall comply with the applicable requirements for alterations in § 36.402 and §§ 36.404...
-
7(2)(b)(vi)
(vi) Bathtubs and tub/showers located in the bathroom provide a clear access aisle adjacent to the lavatory that is at least 2'6" wide and extends for a length of 4'0" (measured from the...
-
1132A.3, Item 2
Swinging doors shall provide a net clear opening width of not less than 32 inches (813 mm), measured with the door or doors positioned at an angle of 90 degrees from the closed position....
-
1132A.3, Item 2
Swinging doors shall provide a net clear opening width of not less than 32 inches (813 mm), measured with the door or doors positioned at an angle of 90 degrees from the closed position....
-
§ 38.119(a)
(a) Any stepwell, or doorway with a lift, ramp or bridge plate, shall have, when the door is open, at least 2 foot-candles of illumination measured on the step tread, ramp, bridge plate...
-
§ 38.81(a)
(a) Any stepwell or doorway with a lift, ramp or bridge plate immediately adjacent to the driver shall have, when the door is open, at least 2 foot-candles of illumination measured on the...
-
1133A.2.1 Clear width
Kitchens shall have a minimum clear width measured between any cabinet, countertop or the face of any appliance (excluding handles and controls) that projects into the kitchen and the opposing...
-
Access-Able Designs Tub Transfer Bench SH-414-2SDL
Measures 25" W x 15" D. Custom sizes available. 5 year warranty....
-
1002.5.2 Transfer Height
The height of amusement ride seats designed for transfer shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
703.5.8 Character Spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....
-
703.5.8 Character Spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....
