Shear force induced in a fastener or mounting device from the application of 250 lbf (1112N) shall be less than the allowable lateral load of either the fastener or mounting device or the supporting...
Search Results "Leg Supports"
Filters
Commonly Searched Documents
-
4.26.3(3)
-
11B-609.8 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the grab bar, fastener, mounting device, or supporting...
-
11B-903.6 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting...
-
Protrusion Limits: ADA Standard Section 307.2
Section 307.2 covers the current ADA Standards for protrusion limits.
-
Classroom Acoustics: ADA Standard Section 6.
Review the updated information on the revisions to the ADA Standards regarding classroom acoustics.
-
Toe Clearance: ADA Standard Section 604.8.1.4
Section 604.8.1.4 covers the current ADA Standards for toe clearance at wheelchair accessible compartments.
-
11B-307.2 Protrusion limits
For example, awnings and their supporting structures cannot reduce the minimum required vertical clearance....
-
M301.4 Lift Compatibility
An overhead lift (and possibly a gurney-based transfer) may be used in lieu of the provisions for clearances in or around the base of equipment to accommodate the legs of portable floor...
-
M301.1 General
Diagnostic equipment that supports patients in a supine, prone, or side-lying position shall comply with M301. ...
-
11B-602.5 Spout location
The spout shall be located 15 inches (381 mm) minimum from the vertical support and 5 inches (127 mm) maximum from the front edge of the unit, including bumpers. ...
-
4.26.3(4)
a direct tension force of 250 lbf (1112N) plus the maximum moment from the application of 250 lbf (1112N) shall be less than the allowable withdrawal load between the fastener and the supporting...
-
Research Issues
NIH Mission As you all probably know, much of the biomedical research in the United States is supported by the NIH....
-
Pilot Rock WXT and WXTH Picnic Table Using Lumber
The unique frame design includes two wheelchair spaces plus provides proper support under the outside ends of the full length seats....
-
Pilot Rock WUT and WUTH Picnic Table Using Recycled Plastic
The unique frame design includes two wheelchair spaces plus provides proper support under the outside ends of the full length seats....
-
Pilot Rock WUT and WUTH Picnic Table Using Formed Steel Channel
The unique frame design includes two wheelchair spaces plus provides proper support under the outside ends of the full length seats....
-
Pilot Rock WXT and WXTH Picnic Table Using Recycled Plastic
The unique frame design includes two wheelchair spaces plus provides proper support under the outside ends of the full length seats....
-
Pilot Rock WXT and WXTH Picnic Table Using Expanded Steel
The unique frame design includes two wheelchair spaces plus provides proper support under the outside ends of the full length seats....
-
Pilot Rock WUT and WUTH Picnic Table Using Lumber
The unique frame design includes two wheelchair spaces plus provides proper support under the outside ends of the full length seats....
-
E207.1 General
EXCEPTION: Software that is assistive technology and that supports the accessibility services of the platform shall not be required to conform to the requirements in Chapter 5....
-
601.1 Scope (Section-by-Section Analysis)
601.1 Scope (Section-by-Section Analysis) This section proposes that the technical requirements for support documentation and services in this chapter be applied where either (a) required...
-
Alterations to cells. (Section-by-Section Analysis)
Only one commenter expressed support for Option I, and a handful of commenters supported Option III. The comments on each option are discussed below....
-
Rakks® Brackets Installation Video
The signature Rakks Style Bracket features a distinctive rectangular bar design that can support shelves up to 24” deep. Rakks style brackets are designed to “underhang” the shelf....
-
602.5 Spout Location
The spout shall be located 15 inches (380 mm) minimum from the vertical support and 5 inches (125 mm) maximum from the front edge of the unit, including bumpers....
-
602.5 Spout Location
The spout shall be located 15 inches (380 mm) minimum from the vertical support and 5 inches (125 mm) maximum from the front edge of the unit, including bumpers....
