The handrail requirements in section 505 address specifications for continuity, height, clearance, gripping surface, cross section, fittings, and extensions....
Search Results "Dining Surface"
Filters
Commonly Searched Documents
-
Handrails Requirement
-
Other international standards
Australian NATSPEC Reference Volume 1: Building Works, Concrete Finishes Section Three classes of surface finish based on using a straightedge method of testing: Class A...
-
III. Results of the Study
Table 10 shows the surface materials recommended by region and surface composition....
-
804.3 Kitchen Work Surface
In residential dwelling units required to comply with 809, at least one 30 inches (760 mm) wide minimum section of counter shall provide a kitchen work surface that complies with 804.3....
-
804.3 Kitchen Work Surface
In residential dwelling units required to comply with 809, at least one 30 inches (760 mm) wide minimum section of counter shall provide a kitchen work surface that complies with 804.3....
-
Observations and Results
After playing for several minutes on each surface, the children were asked to stand on the surface they preferred....
-
606.5 Exposed Pipes and Surfaces
There shall be no sharp or abrasive surfaces under lavatories and sinks. [ECTCR UFAS 4.19.4, 4.24.6, 4.34.6.5(8)]...
-
Figure 302.3 Elongated Openings in Floor or Ground Surfaces – Drawing from the U.S. Access Board
-
1.1.3
1.1.3 A maximum overall design running slope for exterior accessible surfaces (other than ramps), such as sidewalks, of 4% (approximately 1:25) is recommended....
-
17. Can broken or older ground level play components be replaced without changing the surface?
Can broken or older ground level play components be replaced without changing the surface? Yes....
-
11B-606.5 Exposed pipes and surfaces
11B-606.5 Exposed pipes and surfaces. Water supply and drain pipes under lavatories and sinks shall be insulated or otherwise configured to protect against contact....
-
Firmness
The degree of surface resistance to deformation, especially by indentation or the movement of objects (U.S. Access Board, 2007)....
-
RecGrass Synthetic Grass Ground Surface System Section
Requires the Premium User plan or above. (Login or upgrade your account!) -
Stable
A surface is not permanently affected by expected weather conditions and can sustain normal wear and tear from the expected use(s) of the area, between planned maintenance....
-
Analysis of Transfer Surface Dimensions Based on Wheeled Mobility User Anthropometry
Access Board RE: Analysis of Transfer Surface Dimensions Based on Wheeled Mobility User Anthropometry...
-
2) Where the Standard says "Changes in level are not permitted"
permitted", such as 304.2 for turning spaces: Here the standard is followed by an unenforceable advisory that says, "As used in this section, the phrase ‘changes in level’ refers to surfaces...
-
E. Level Surface
Are the level surfaces of accessible parking spaces and access aisles free of "built-up" curb ramps so persons who use mobility aids (e.g.: wheelchairs, walkers or crutches) can make convenient...
-
5.2.2.2 Transfer Surface Depth
5.2.2.2 Transfer Surface Depth. The transfer surface should be 17 inches deep minimum for equipment used by patients in a seated position....
-
Current industry standard practices resulting from this project
and the National Concrete Masonry Association, funded research in 2002 to evaluate the vibration exposure during electric and manual wheelchair propulsion over several types of sidewalk surfaces...
-
5.2.2.1 Transfer Surface Width
5.2.2.1 Transfer Surface Width. The transfer surface should be 21 inches wide minimum for examination chairs and other equipment used by patients in a seated position....
-
6. Recognize that Proper Installation of Play Surface Systems is Key
Recognize that Proper Installation of Play Surface Systems is Key An accessible surface system can be rendered useless if it is not properly installed....
-
Q5.) What dimensions and conditions can practitioners reasonably consider to be compliant when the conditions, as constructed, do not meet the technical requirements exactly and there are no official, published, industry-developed tolerances?
Sloped concrete and asphalt surfaces are an excellent example of this problem. ...
-
4. Assess During the Planning, Installation and Maintenance Phases
Assess During the Planning, Installation and Maintenance Phases Once the playground surface is installed, an on-site inspection of the surface system should be conducted along the accessible...
-
Hager Companies Door Protection Plate 198S
Door Protection Plate 198S 0.038" gauge stainless steel Materials: - Stainless Steel
