Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical.
Search Results "Wheelchair Size"
Filters
Commonly Searched Documents
-
M303.3.1 Vertical
-
M303.3.2 Beveled
Changes in level between ¼ inch (6.4 mm) high and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2.
-
M303.2.4.2 Knee Clearance
Knee clearance shall be provided at a depth of 11 inches (280 mm) minimum and 25 inches (635 mm) maximum at 9 inches (230 mm) above the floor and at a depth of 8 inches (205 mm)...
-
Release of unsold accessible seats. (Section-by-Section Analysis)
The Department believes that guidance in this area is needed, but also recognizes that ticketing practices and policies vary with venue size and event type, and that a "one-size-fits-all...
-
Section 36.308 Seating in Assembly Areas (Section-by-Section Analysis)
Proposed § 36.308(a)(1)(iii) provides that companion seats may be fixed or movable and that they shall be equivalent in size, quality, comfort, and amenities to the other seats in the assembly...
-
Ticket sales. (Section-by-Section Analysis)
‘‘Accessible seating'' is defined in § 35.138(a)(1) of the final rule to mean ‘‘wheelchair spaces and companion seats that comply with sections 221 and 802 of the 2010 Standards along with...
-
Figure 604.8.1.2 Wheelchair Accessible Toilet Compartment Doors – Drawing from the U.S. Access Board
-
5.8.2.1 Height of Breast Platform at Time of Measurement
These dimensions (27 and 34-inch heights) are the same as those defined by the current 2010 Standards to accommodate wheelchair users at desks, which is outlined by the dotted lines in Figure...
-
Clearances
Clearances Wheelchair spaces on amusement rides must comply with the following provisions, with three exceptions: Securement devices may overlap required clearances....
-
Gaps: ADA Standard Section 1002.4.3
Floors of amusement rides with wheelchair spaces and floors of load and unload areas shall be coordinated so that, when amusement rides are at rest in the load and unload position, the vertical...
-
6.10
requirements Standard 4.33.3, and §§ 221 and 802 of the ADA and ABA Accessibility Guidelines for Buildings and Facilities, as published in the Federal Register on July 23, 2004, to (a) provide wheelchair...
-
M303.3.3 Ramped (Section-by-Section Analysis)
The MDE NPRM proposed that for equipment with a change in level at the entry of a wheelchair space, level changes greater than ½ inch high would be required to be ramped and comply with...
-
4. Breast Platform Adjustability
the body parts of a patient while seated in a wheelchair (proposed M303.4)....
-
5. Edge Protection
The Access Board sought public input with question 30 in the MDE NPRM preamble, on whether there is diagnostic equipment with wheelchair spaces on raised platforms that does not provide...
-
§ 38.53(a)(2)
If doorways connecting adjoining cars in a multi-car train are provided, and if such doorway is connected by an aisle with a minimum clear width of 30 inches to one or more spaces where wheelchair...
-
F206.2.8.2 Wheelchair Spaces, Ride Seats Designed for Transfer, and Transfer Devices
When amusement rides are in the load and unload position, wheelchair spaces complying with 1002.4, amusement ride seats designed for transfer complying with 1002.5, and transfer devices...
-
206.2.9.2 Wheelchair Spaces, Ride Seats Designed for Transfer, and Transfer Devices
When amusement rides are in the load and unload position, wheelchair spaces complying with 1002.4, amusement ride seats designed for transfer complying with 1002.5, and transfer devices...
-
10) Assembly areas
10) Assembly areas ADAAG: * Wheelchair seating: Requirements triggered in any assembly area with fixed seating that seats four or more people....
-
T602.3 Approach
One full unobstructed side of each wheelchair space shall adjoin or overlap a passenger access route....
-
Secondary market ticket sales. (Section-by-Section Analysis)
Question 21: Are there particular concerns about the obligation imposed by the proposed rule in which a public entity must provide accessible seating, including a wheelchair space where...
-
Inpro Corporation ENDURANT® Ceiling Hung Partitions
Our celling Hung privacy partitions are manufactured from BioPrism® Solid Surface featuring an industry leading bio-resin blend. Features & Benefits Ideal for...
-
Inpro Corporation ENDURANT® Floor-to-Ceiling Mounted Partitions
Features & Benefits Ideal for healthcare, education and corporate environments Utilizing a reinforced wood core, BioPrism® Privacy Partitions are comprised...
