Designations and indicators of car controls shall comply with 407.4.7.
Search Results "Non-Positive Shut Off"
-
408.4.7 Designations and Indicators of Car Controls
-
408.4.7 Designations and Indicators of Car Controls
408.4.7 Designations and Indicators of Car Controls. Designations and indicators of car controls shall comply with 407.4.7.
-
B. The ADA Standards for Accessible Design
A clear floor or ground space complying with 305 shall be positioned for a parallel approach adjacent to the 36 inch (915 mm) minimum length of counter....
-
1(3) Exceptions to site impracticality
(3) Exceptions to site impracticality. Regardless of site considerations described in paragraphs (1) and (2), an accessible entrance on an accessible route is practical when:
-
A4.30.5 Finish and Contrast
An eggshell finish (11 to 19 degree gloss on 60 degree glossimeter) is recommended. Research indicates that signs are more legible for persons with low vision when characters...
-
4.30.3* COLOR CONTRAST
Characters and symbols shall contrast with their background - either light characters on a dark background or dark characters on a light background.
-
M302.4.1 Clearance in Base
The base of the diagnostic equipment shall provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep...
-
C. M303 Diagnostic Equipment Used by Patients Seated in a Wheelchair
M303 contains the technical requirements for diagnostic equipment used by patients seated in wheelchairs. In the final rule the Access Board made four significant changes to this...
-
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces.
-
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces Recommendations
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces Recommendations
-
M302.4.1 Clearance in Base
The base of the equipment shall provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum...
-
Washing Machines; Clothes Dryers— Sections 214.2 and 214.3 of the 2010 Standards
These requirements apply to each laundry room except that HUD’s Section 504 regulation and UFAS would not require a laundry room on an upper story of a non-elevator building to be accessible...
-
M302.4 Lift Compatibility (Section-by-Section Analysis)
The MDE NPRM proposed to require that diagnostic equipment used by patients in the seated position be usable with a patient lift and comply with either the proposed clearance in base (proposed...
-
M305.3.1 Length (Section-by-Section Analysis)
(Significant Changes – Standing Supports), the final rule requires that horizontal standing supports be positioned horizontally in relation to standing surfaces and retains the proposed...
-
11B-209.2.1 Passenger drop-off and loading zones
Passenger drop-off and loading zones, except those required to comply with Sections 11B-209.2.2 and 11B-209.2.3, shall provide at least one passenger drop-off and loading zone complying...
-
11B-209.2.1 Passenger drop-off and loading zones
Passenger drop-off and loading zones, except those required to comply with Sections 11B-209.2.2 and 11B-209.2.3, shall provide at least one passenger drop-off and loading zone complying...
-
A. Question 1: Applicability of Section 904.4.1’s Exception
Section 904.4.1 and its exception both require that a sales or service counter be “36 inches (915 mm) high maximum above the finish floor,” and Section 904.4.1 further requires that...
-
11B-220.2 Point-of-sale devices
In addition, point-of-sale systems that include a video touch screen or any other non-tactile keypad shall comply with either Section 11B-707.9.1.1 _|Tactilely Discernible Numerical Keypad...
-
T404 Level Boarding and Alighting
[See subsections ...]
-
T204.2 Doorways with Lifts, Ramps or Bridgeplates
Doorways with lifts or ramps shall comply with T502.2.
-
11.2 Q. Under the individual building test, at what point of the planned entrance is the measurement taken?
A. On a horizontal plane, the center of each individual doorway should be the point of measurement when measuring to an arrival point, whether the doorway is an entrance door to the...
-
M305.3.1 Length
The length of gripping surfaces for standing supports shall be based on the position of the standing supports in relation to the standing surfaces they serve....
-
11B-305.5 Position
Unless otherwise specified, clear floor or ground space shall be positioned for either forward or parallel approach to an element. ...