Where the diagnostic equipment is used in a reclined position, head and back support shall be provided and shall comply with M305.5....
Search Results "Equipment Room"
-
M301.3.3 Head and Back Support
-
L. Accessible Guest Rooms
Accessible Guest Rooms (1) Defendants will have 12 designated accessible rooms/ suites that comply with the 2010 Standards dispersed among the various classes of accommodations as follows...
-
Healthcare Stories - Carol Gill and Larry Voss Part 1 of 6
Requires the Registered User plan or above. Login! -
Error/Omission: Doors into and within guest rooms that are not accessible guest rooms do not provide at least 32" clear opening width.
Error/Omission: Doors into and within guest rooms that are not accessible guest rooms do not provide at least 32" clear opening width....
-
Spectrum Industries Inc. Freedom One Sit-to-Stand Lectern™
Not only is the Freedom One ADA compliant, there is an astounding 36 rack units to keep all audio visual equipment in one place. ...
-
11B-405.5 Clear width
Exceptions: Within employee work areas, the required clear width of ramps that are a part of common use circulation paths shall be permitted to be decreased by work area equipment...
-
11B-405.5 Clear width
Exceptions: Within employee work areas, the required clear width of ramps that are a part of common use circulation paths shall be permitted to be decreased by work area equipment...
-
11B-213.2.1 Unisex (single-user or family) toilet and unisex (single-user or family) bathing rooms
Unisex (single-user or family) toilet rooms shall contain not more than one lavatory, and not more than two water closets without urinals or one water closet and one urinal....
-
11B-213.2.1 Unisex (single-user or family) toilet and unisex (single-user or family) bathing rooms
Unisex (single-user or family) toilet rooms shall contain not more than one lavatory, and not more than two water closets without urinals or one water closet and one urinal....
-
11B-213.2.2 Unisex (Patient) toilet rooms in medical care and long-term care facilities
Common-use unisex toilet rooms for exclusive patient use not located within patient bedrooms shall contain a lavatory and one water closet....
-
11B-213.2.2 Unisex (Patient) toilet rooms in medical care and long-term care facilities
Common-use unisex toilet rooms for exclusive patient use not located within patient bedrooms shall contain a lavatory and one water closet....
-
4.35.5 Mirror
Where mirrors are provided in dressing rooms of the same use, then in an accessible dressing room, a full-length mirror, measuring at least 18 in wide by 54 in high (460 mm by 1370 mm),...
-
M101.6 Dimensional Tolerances
Dimensions are subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions.
-
Chapter 2: Scoping
[See subsections ...]
-
Section 1193.31 Accessibility and usability (Section-by-Section Analysis)
Section 1193.31 Accessibility and usability (Section-by-Section Analysis) This section provides that, subject to section 1193.21, manufacturers must design, develop and fabricate...
-
M307.3 Operation
Operable parts shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist.
-
M307.1 General
Operable parts for patient use shall comply with M307.
-
M102.1 Defined Terms
For the purpose of the MDE Standards, the following terms have the indicated meaning:
-
M102 Definitions (Section-by-Section Analysis)
This is an introductory section.
-
M307.1 General (Section-by-Section Analysis)
This is an introductory section.
-
M307.3 Operation (Section-by-Section Analysis)
The MDE NPRM proposed to require operable parts to be operable with one hand and not require tight grasping, pinching, or twisting of the wrist. There were no public comments on this...
-
MITA Advisory Committee Members
MITA Advisory Committee Members MINORITY REPORT ON TRANSFER SURFACE HEIGHT RECOMMENDATIONS OF THE U.S. ACCESS BOARD ADVISORY COMMITTEE RE: NPRM: M301.2.1 AND M302.2.1 HEIGHT
-
M307.3 Operation
Operable parts shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist.
-
M101.5 Dimensional Tolerances
Dimensions are subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions
