ADA and ANSI compliant Clean, contemporary lines Flat bottom design maximizes basin capacity for multipurpose use Basin constructed of vandal-resistant Terreon Solid Surface Material...
Search Results "LU/LA: Limited Use/Limited Application Elevator"
Commonly Searched Documents
- Bradley Oval Multipurpose Basin HS-TO1
- Bradley Rectangular Multipurpose Basin HS-TR1
-
11B-216.6 Entrances
where the accessible route diverges from the route for the general public and should be located at decision points (for example where the path to the stairs diverges from the path to an elevator...
-
Triggering event
Three commenters supported the use of “start of construction’’ as the triggering event....
-
7.1 Introduction
This chapter discusses the application of nondiscrimination requirements to other employment practices and activities....
-
F247.4 Trail Facilities
This section requires camping facilities, picnic facilities, and viewing areas provided on trails to comply with the applicable scoping requirements for the facilities in F244 through F246...
-
F245.2.5 Elements within Picnic Units with Mobility Features
Where these elements are provided within a picnic unit, at least one of each type of element is required to comply with the applicable technical requirements for the element....
- Besam SL500 Surface Mount Automatic Sliding Door
- Cal-Royal 700 Series Hydraulic Door Closers
- Besam SW200i Overhead Concealed Swing Door Operator
-
11B-604.3.2 Overlap
ETA Editor's Note The Office of Statewide Health Planning and Development (OSHPD), which has jurisdiction over hospitals and long-term care facilities in California, issued Code Application...
- Sargent 281 Series Cast Iron Door Closer
-
1009.15 Handrails
[DSA-AC] For applications listed in Section 1.9.1 regulated by the Division of the State Architect-Access Compliance, see Chapter 11B, Sections 11B-504.6 and 11B-505....
-
§382.159(b)
(b) Any person believing that a carrier has violated any provision of this part may also file a formal complaint under the applicable procedures of 14 CFR part 302....
-
§382.9(a)
(a) If you are a foreign carrier, and you believe that an applicable provision of the law of a foreign nation precludes you from complying with a provision of this part, you may request...
-
§ 35.150(b)(5) Exemption for small facilities
For measures taken to comply with the program accessibility requirements of this section, existing facilities shall comply with the applicable requirements for alterations in § 35.151 of...
-
§8.13(b)
(b) When a recipient is undertaking affirmative action efforts, voluntary or otherwise, the recipient may invite applicants for employment to indicate whether and to what extent they are...
-
17. In § 38.113, amend paragraph (d)(3)
In § 38.113, amend paragraph (d)(3) by removing the period at the end of the paragraph and adding the words “ensuring compliance with section 37.42, where applicable” in its place....
-
C205.1 General (Section-by-Section Analysis)
C205.1 General (Section-by-Section Analysis) This section proposes that, where components of ICT transmit information or have a user interface, they must conform to the applicable provisions...
-
§100.147 Adjudication.
[62 FR 66433, Dec. 18, 1997] An aggrieved person, complainant, department or agency that challenges a privilege asserted under §100.144 may seek a determination of the existence and application...
-
F246.3 Outdoor Constructed Features
This section requires at least 20 percent, but not less than one, of each type of outdoor constructed feature provided within viewing areas to comply with the applicable technical requirements...
-
§1630.6(a) In general
It is unlawful for a covered entity to participate in a contractual or other arrangement or relationship that has the effect of subjecting the covered entity's own qualified applicant or...
-
11B-202.3 Alterations
Where existing elements or spaces are altered, each altered element or space shall comply with the applicable requirements of Division 2, including Section 11B-202.4."...
-
11B-703.3.2 Position
Exception: Braille provided on elevator car controls shall be separated 3/16 inch (4.8 mm) minimum and shall be located directly below the corresponding raised characters or symbols....