[See subsections ...]
Search Results "Surface Slope"
-
403 Walking Surfaces
-
Handrails Along Walking Surfaces [§403.6, §505]
Handrails along Walking Surfaces 34” – 38” high measured to the top of the gripping surface....
-
C1-f
If the slope of part of the accessible route is more than 1:20, does it meet the following requirements for an accessible ramp? Yes No...
-
Why a smooth surface door or kickplate is important
And those nicks slice your fingers like butter when you least expect it.
-
E1-d
Where the slope of the accessible route is greater than 1:20, does this area meet the following requirements for an accessible ramp? Yes No...
-
Installation of Test Surfaces
Installation of Test Surfaces In accordance with standard EWF design and construction practice (Figure 2), the full depth surfaces were prepared to the same requirements needed for permanent...
-
410.2 Floor Surfaces
410.2 Floor Surfaces. Floor surfaces in platform lifts shall comply with 302 and 303....
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
609.5 Surface Hazards
609.5 Surface Hazards. Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....
-
11B-1005.3.2 Extended ground or deck surface
The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing....
-
11B-1005.3.2 Extended ground or deck surface
The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing....
-
a. Transfer Surface Adjustability
The MDE NPRM proposed that the same transfer surface height range of 17 inches minimum to 19 inches maximum be applied to both diagnostic equipment used in the supine, prone, or side-lying...
-
Handrail Gripping Surfaces: ADA Standard Section 1008.2.5.3.1
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
Door and Gate Surfaces [§404.2.10]
Door and Gate Surfaces [§404.2.10] The bottom surface of doors and gates on the push side must be smooth to a height of at least 10”....
-
Technical Bulletin: Ground and Floor Surfaces
UNITED STATES ACCESS BOARD A FEDERAL AGENCY COMMITTED TO ACCESSIBLE DESIGN Technical Bulletin: Ground and Floor Surfaces...
-
Firmness, Stability, and Slip Resistance [§302.1]
Firmness, Stability, and Slip Resistance [§302.1] Accessible floor and ground surfaces must be stable, firm, and slip resistant....
-
IV. Discussion of Findings and Implications
of surface maintenance to assure accessibility and safety for use by children on a daily basis. ...
-
Macro Supa-Trac Heavy Duty Ground Surface
Panel (sq ft/pc): 2.26 Shipping (sq ft): Trailer 53′: 21,969, Trailer 48′: 20,250, Flatbed 48′: 21,969 Static Compression Capacity (lbs/sq ft): 36,000* *Solid sub-surface...
-
11B-902.4 Dining surfaces and work surfaces for children’s use
Accessible dining surfaces and work surfaces for children’s use shall comply with Section 11B-902.4....
-
11B-902.4 Dining surfaces and work surfaces for children’s use
Accessible dining surfaces and work surfaces for children’s use shall comply with Section 11B-902.4....
-
11B-902.4 Dining surfaces and work surfaces for children’s use
Accessible dining surfaces and work surfaces for children’s use shall comply with Section 11B-902.4....
-
410.2 Floor Surfaces
Floor surfaces in platform lifts shall comply with 302 and 303....
