car floor height with the inner barrier (if applicable) down or retracted, gaps between the forward lift platform edge and car floor shall not exceed 1/2 inch horizontally and 5/8 inch vertically...
Search Results "Vertical Plane"
Filters
Commonly Searched Documents
-
§ 38.125(b)(7) Platform gaps
-
11B-1008.3.2.3 Transfer supports
Some examples of supports include a rope loop, a loop type handle, a slot in the edge of a flat horizontal or vertical member, poles or bars, or D rings on the corner posts. ◼...
-
11B-704.5 TTY shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (152 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
Corbin Russwin Inc. ED4000 Series Narrow Stile Exit Device
Available in Rim, Surface Vertical Rod, Concealed Vertical Rod and electrified, the ED4000 Series meets all your aluminum and metal door needs....
-
704.5 TTY Shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (150 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
ENTRANCE
An entrance includes the approach walk, the vertical access leading to the entrance platform, the entrance platform itself, vestibules if provided, the entry door(s) or gate(s), and the...
-
Mezzanines (Private and Public Sector Facilities) [§206.2.4, Ex. 3]
Mezzanines (Private and Public Sector Facilities) [§206.2.4, Ex. 3] An accessible route must serve mezzanines in multi-story facilities where vertical access between stories is required...
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
11B-504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
DORMA 8000 Series Exit Device
Economical and reliable exit device Rim, surface vertical rod, and surface vertical rod ''less bottom rod,'' along with a full range of trim options which allow access from the secure...
-
M301.2.1, M302.2.1 Transfer Height
These surfaces may range between 4” to 5” in thickness - this will add to the vertical height of a stretcher when measuring from the floor to the top of the surface (uncompressed)....
-
206.2.3 Multi-Story Buildings and Facilities
Exceptions 1 – 7 are preempted by Florida vertical accessibility requirements of s. 553.509, F.S., as incorporated in section 201.1.1....
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical and...
-
206.2.4 Spaces and Elements
Exceptions 1 – 3 are preempted by Florida vertical accessibility requirements of s.553.509, F.S., as incorporated in section 201.1.1....
-
Sight Lines
Sight Lines Both the horizontal and vertical viewing angles must be considered in the design of assembly areas....
-
Transfer Supports (M301.3.1, M302.3.1, and M305.2)
M305.2.2 would require the transfer supports and their connections to be capable of resisting vertical and horizontal forces of 250 pounds applied to all points of the transfer support....
-
R408.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
Running Slope
This may be expressed as the percentage of change in elevation (grade) or as a ratio of vertical distance to horizontal distance (running slope)....
-
1) Where the Standard specifically refers to 303
1) Where the Standard specifically refers to 303, such as 403.4 changes in level for walking surfaces: Here it is clear that changes in level that comply with either the ¼" maximum vertical...
-
Edge Protection [§405.9]
Edge protection is not required at: ramps no higher than 6” that have side flares ramp landings serving an adjoining run or stairway sides of ramp landings with vertical...
-
11B-704.5 TTY shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (152 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
§ 38.159(b)(10) Platform movement
The maximum platform horizontal and vertical acceleration when occupied shall be 0.3g....
-
4.2 Stretchers
First, to serve these multiple purposes, the current configuration of stretchers must accommodate the vertical height needs of numerous components, including (Figure 3.1): the basic elements...
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
