A public accommodation is urged to take measures to comply with the barrier removal requirements of this section in accordance with the following order of priorities....
Search Results "Measuring Instrument"
-
Sec.36.304(c) Priorities
-
Technical Requirements
Are the specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
1013.4 Height
This section requires tent platforms to be 19 inches high maximum measured from the clear ground space to the tent platform surface....
-
Technical Requirements
The specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.). ...
-
1014.2.1.2 Floor Height
The camp shelter floor at the entrance shall be 19 inches (485 mm) high maximum measured from the clear ground space....
-
1.6.17 Sterile Area.
A portion of an airport, specified in the airport security program, in which certain security measures specified in 49 CFR part 1542, Airport Security, are carried out....
-
604.4 Seats
The seat height of a water closet above the finish floor shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured to the top of the seat....
-
2. Referenced Documents
2.1 ASTM standards E867 Standard Terminology Relating to Vehicle-Pavement Systems E1364 Standard Test Method for Measuring Road Roughness by Static Level Method E1926 Standard...
-
Acknowledgments
Acknowledgments The development of objective surface measurement devices and objective surface testing was conducted with funding from the National Center for Medical Rehabilitation Research...
-
604.4 Seats
The seat height of a water closet above the finish floor shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured to the top of the seat....
-
11B-609.4 Position of grab bars
Grab bars shall be installed in a horizontal position, 33 inches (838 mm) minimum and 36 inches (914 mm) maximum above the finish floor measured to the top of the gripping surface, except...
-
604.4 Seats
The seat height of a water closet above the finish floor shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured to the top of the seat....
-
604.4 Seats
The seat height of a water closet above the finish floor shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured to the top of the seat....
-
II. Research Methodology
four (4) rounds; however results from the first round made it evident to the research team and the funding agencies that modifications were necessary not only pertaining to the initial instrument...
-
II-1.2000 Public entity
A public entity covered by title II is defined as -- 1) Any State or local government; 2) Any department, agency, special purpose district, or other instrumentality of a State or local...
-
M301.2.3 Size
The size of transfer surfaces shall be measured from center points of their opposing sides....
-
1013.4 Height
Tent platforms shall be 19 inches (485 mm) high maximum measured from the clear ground space to the tent platform surface....
-
702.9.1 TIA-1083-B
Telecommunications—Communications Products—Handset Magnetic Measurement Procedures and Performance Requirements, October 2015, IBR approved for Appendix C, Section 412.3.2....
-
§ 35.151(b)(2)
(2) The path of travel requirements of § 35.151(b)(4) shall not apply to measures taken solely to comply with the program accessibility requirements of this section....
-
4.15.2* Spout Height
Spouts shall be no higher than 36 in (915 mm), measured from the floor or ground surfaces to the spout outlet (see Fig. 27(a))....
-
Side Approach
Side Approach The maximum reach depth for a high (54 inch maximum) reach is 10 inches, measured from the clear floor space....
-
1013.4 Height
Tent platforms shall be 19 inches (485 mm) high maximum measured from the clear ground space to the tent platform surface....
-
1.2.4
1.2.4 When local horizontal discontinuities and vertical alignments are measured according to Section 1.1.9 a recommended tolerance is ±1/8 in. (3 mm)....
-
11B-1009.4.2 Height
The height of the transfer wall shall be 16 inches (406 mm) minimum and 19 inches (483 mm) maximum measured from the deck....