Hager Push/Pull Latch 311L: - Engraving available (optional) - Lead lined - Non-handed - Hospital Latch - 311L is same as 311H but for use on lead lined doors - *Horizontal...
Search Results "Horizontal Dispersion"
-
Hager Companies Push/Pull Latch 311L
-
NFPA
of a smoke alarm required by other sections of the code. 7) Smoke alarms and smoke detectors shall not be installed within a 36 in. (910 mm) horizontal path from the supply registers...
-
505.10.2 Top Extension at Stairs
At the top of a stair flight, handrails shall extend horizontally above the landing for 12 inches (305 mm) minimum beginning directly above the first riser nosing....
-
f-v
If a ramp is more than 30 feet long, is a level landing at least 60 inches long provided at every 30 feet of horizontal length?...
-
4d.
If a ramp is more than 30 feet long, is a level landing at least 60 inches long provided every 30 feet of horizontal length?...
-
6d. Ramp Length
If a ramp is more than 30 feet long, is a level landing at least 60 inches long provided every 30 feet of horizontal length?...
-
Extensions
Handrails that are not continuous must have horizontal extensions at both the top and bottom of the ramp at least 12 inches long that are rounded or returned smoothly to walls, posts, or...
-
Pressalit Care PLUS Support Arm Height and Sideways Adjustable Swing Grab Bar
For fitting to horizontal wall track (not included). Maximum load: 330lbs. (150 kg)...
-
233 Residential Facilities, F233 Residential Facilities
233.3.6 Dispersion ABA Scoping Requirements F233 Residential Facilities F233 Residential Facilities F233.1 General F233.1 General ...
-
Window Ease
Window Ease™ attaches to any manufactured single-hung, double-hung or horizontal sliding window....
-
Southwest Home Products Window Ease Latching System
Modifies New or Existing Windows For Vertical or Horizontal Sliding Windows Compliance with All Codes Guaranteed Window EaseTM is not a window....
-
11B-809.10.5.2 Reinforcement for grab bars
Grab bar backing shall be installed horizontally to permit the installation of a 48-inch (1219 mm) grab bar with each end 6 inches (152 mm) maximum from the end walls of the bathtub....
-
11B-809.10.5.2 Reinforcement for grab bars
Grab bar backing shall be installed horizontally to permit the installation of a 48-inch (1219 mm) grab bar with each end 6 inches (152 mm) maximum from the end walls of the bathtub....
-
F216.4.1 Exit Doors
An exit passageway is a horizontal exit component that is separated from the interior spaces of the building by fire-resistance-rated construction and that leads to the exit discharge or...
-
216.4.1 Exit Doors
An exit passageway is a horizontal exit component that is separated from the interior spaces of the building by fire-resistance-rated construction and that leads to the exit discharge or...
-
Running Slope
This may be expressed as the percentage of change in elevation (grade) or as a ratio of vertical distance to horizontal distance (running slope)....
-
4.1.7(3)(e)
Exhibits and signage displayed horizontally (e.g., open books), should be no higher than 44 in (1120 mm) above the floor surface....
-
1009.6.4 Separation
Each area of refuge shall be separated from the remainder of the story by a smoke barrier complying with Section 709 or a horizontal exit complying with Section 1026....
-
§ 38.159(b)(10) Platform movement
The maximum platform horizontal and vertical acceleration when occupied shall be 0.3g....
-
3. Buttock-Popliteal Length
Buttock-Popliteal Length For this study, an estimate of buttock-popliteal length was calculated as the horizontal distance from the proximal (rear) edge of the wheelchair seat cushion...
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other. Cavities created by added kick plates shall be capped....
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical and horizontal...
-
711.3.2 Membrane penetrations
By a horizontal distance of not less than 24 inches (610 mm); 1.2....
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other....
