For such a measurement, the top of the breast platform will be moved to 34 inches above the ground, and then the clearance dimensions will be measured just as they would be on any stationary...
Search Results "Children's Dimension"
Filters
Commonly Searched Documents
-
5.8.2.8 Knee and Toe Clearance Recommendations Summary
-
Parking
PARKING Location and number of van parking and standard parking spaces. 11B-208 Dimensions of accessible parking spaces and access...
-
Parking
PARKING Location and number of van parking and standard parking spaces. 11B-208 Dimensions of accessible parking spaces and access...
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
11B-812.10.4 Location
Where the long dimension of a vehicle space is parallel to the vehicular way, the EV charger shall be adjacent to, and 48 inches (1219 mm) maximum from the head end or foot end of the vehicle...
-
Investigation
During the course of the investigation, the United States determined that LCG: (i) refused to provide assistance with insulin administration (by pen or syringe) to children with Type...
-
Technical requirements
Technical requirements state the specific numbers, conditions, and measurements that are required (percent that must comply, dimensions, reach ranges, grades, trail width, and so forth)....
-
§ 38.4(b) Dimensional tolerances
All dimensions are subject to conventional engineering tolerances for material properties and field conditions, including normal anticipated wear not exceeding accepted industry-wide standards...
-
M305.3 Standing Supports (Section-by-Section Analysis)
In the MDE NPRM preamble, the Access Board noted that it was considering adopting the cross section dimensions for grab bars from the 2004 ADA and ABA Accessibility Guidelines and applying...
-
M101.6 Dimensional Tolerances (Section-by-Section Analysis)
The MDE NPRM proposed that dimensions were to be subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions....
-
407.12.3.2.2 Knee and Toe Space (Section-by-Section Analysis)
407.12.3.2.2 Knee and Toe Space (Section-by-Section Analysis) This section proposes dimensions for knee and toe space under ICT when an obstructed forward reach is provided....
-
Clear Floor Space [4.16.2]
the required clear floor space doors cannot swing into the clear floor space required at any fixture the 18 inch water closet centerline is absolute The 18 inch dimension...
-
Floor Plan of Elevator Cars [4.10.9]
The car dimensions specified in ADAAG are based on earlier accessibility guidelines developed in accord with industry standards....
-
Bicycle Trailers
Bicycle Trailers Bicycle trailers are often used to carry children and to transport cargo....
-
III-3.12000 Places of public accommodation located in private residences
In addition, the children will be using the master bathroom....
-
Appendix A: References
Translating general pediatric weight loss interventions for application with children with intellectual and developmental disabilities....
-
VisionConnect™ Mobile App
VisionConnect™ provides a searchable directory of services available in the US and Canada for children and adults who are blind or visually impaired....
-
Elongated surface openings must be perpendicular to the dominant direction of travel, but what if there is no dominant direction of travel?
When there is no dominant direction of cross traffic, openings must be limited to ½” in both dimensions. ...
-
Elevator Car Requirements [§407.4]
Elevator Car Requirements [§407.4] The ADA Standards specify the minimum car dimensions....
-
Chapter 1: Application and Administration
Chapter 1: Application and Administration This chapter states general principles that recognize the purpose of the guidelines (101), provisions for adults and children (102), equivalent...
-
Accessible Passenger Loading Zones [§503]
Accessible Passenger Loading Zones [§503] Requirements for accessible passenger loading zones address vehicle pull-up spaces and access aisles, including their dimensions, surfacing,...
-
M101.5 Dimensional Tolerances
Dimensions are subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions. Question 5....
-
§100.305(f)
(f) For purposes of the transition provision described in §100.305(e)(5), a housing facility or community may not evict, refuse to renew leases, or otherwise penalize families with children...
-
Under what circumstances in non-employment situations, may a public entity require documentation of a disability or information about a person’s medical condition?
For example, a municipal recreation department summer camp requires parents to fill out a questionnaire and to submit medical documentation regarding their children's ability to participate...
