Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (230 mm) above the finish floor or ground....
Search Results "Centered Clear Floor Space"
Commonly Searched Documents
-
306.3.2 Maximum Depth
-
903.5 Height
The top of the bench seat surface shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the finish floor or ground....
-
409.4.4 Leveling
Each car shall automatically stop at a floor landing within a of 1/2 inch (13 mm) under rated loading to zero loading conditions....
-
5.1.4 Transfer Surface Height Measurement
The transfer surface height should be measured from the floor to the highest point on the seat in an uncompressed state, inclusive of bolsters....
-
T304.2 Height
Operable parts shall be located 24 inches (610 mm) minimum and 48 inches (1220 mm) maximum above the floor of non-rail vehicles....
-
11B-306.3.2 Maximum depth
Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (229 mm) above the finish floor or ground....
-
306.3.2 Maximum Depth
Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (230 mm) above the finish floor or ground....
-
4. Overhead Objects
4 Is the voting area free of overhead objects that voters may pass under with the bottom edge lower than 80 inches above the floor? Yes _____ No _____...
-
4.18.4 Flush Controls
Flush controls shall be hand operated or automatic, and shall comply with 4.27.4, and shall be mounted no more than 44 in (1120 mm) above the finish floor....
-
903.5 Height
The top of the bench seat surface shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the finish floor or ground. ...
-
306.3.2 Maximum Depth
Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (230 mm) above the finish floor or ground....
-
4.4.2 Height
The front edge of the seat of a bench shall be at least 17 inches (430 mm) and no more than 19 inches (485 mm) above the floor or ground. ...
-
11B-306.3.2 Maximum depth
Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (229 mm) above the finish floor or ground....
-
§ 38.113(d)(2) Exception
New cars operating in existing stations may have a floor height within plus or minus 11/2 inches of the platform height....
-
11B-903.5 Height
The top of the bench seat surface shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum above the finish floor or ground....
-
11B-903.5 Height
The top of the bench seat surface shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum above the finish floor or ground....
-
11B-306.3.2 Maximum depth
Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (229 mm) above the finish floor or ground....
-
11B-608.1 General
Shower stalls that are 60 inches (1525 mm) wide and have no curb may increase the usability of a bathroom because the shower area provides additional maneuvering space. ◼...
-
Angled (Front-In) Parking
ADAAG's requirement for an access aisle on either side of a space (they can be shared by two spaces) is based on the assumption that drivers can head in or back in as needed....
-
F202.3 Alterations
The final rule adds Exception 4 to this section, which applies to altered elements and spaces....
-
Section 4.1.2, Accessible Sites and Exterior Facilities: New Construction (Section-By-Section Analysis and Response to Comments)
Interior elements and spaces are covered by Sec.4.1.3....
-
Parking
Parking The chart below indicates the number of accessible spaces required by the 2010 Standards. One out of every six accessible spaces must be van-accessible....
- Independent Living Resources - La Crosse, Richland Center, WI
- Ability1st - the Center for Independent Living of North Florida - Tallahassee, FL