Support arm, height adjustable 150 mm. ...
Search Results "Vertical Standing Support"
-
Pressalit Care VALUE Support Arm Height Adjustable
-
Conclusion
Of the participants who attempted and were successful with both two-step transfers, the 50th percentile could attain a 7 inch vertical height difference which is close to the maximum allowable...
-
A. ACCESSIBLE SEATING
Wheelchair Spaces shall be dispersed vertically at varying spaces from the performance area or playing field, and in each balcony or mezzanine, per Standards § 221.2.3.2, and dispersed horizontally...
-
Hand Cycles (Stand-Alone)
Hand Cycles (Stand-Alone) On stand-alone models of hand cycles, the pedaling motion is done with the arms (figures 11 and 12)....
-
2. Standing
Standing 9....
-
Zurn Z1209 Vertical Offset Siphon Jet Water Closet Support System
FEATURES: Vertical, offset water closet carrier 300 lb. load capacity...
-
M305.2.7 Clearance (Section-by-Section Analysis)
In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support....
-
Section 35.151(g) Assembly areas (Section-by-Section Analysis)
The vertical viewing angle is the angle between a horizontal line perpendicular to the seated viewer's eye to the screen and a line from the seated viewer's eye to the top of the screen....
-
M305.2.8 Fittings (Section-by-Section Analysis)
The MDE NPRM proposed to require that transfer supports not rotate in their fittings (proposed M305.2.3). Five commenters addressed this provision....
-
Regulatory Impact Analysis.
Side reach; water closet clearances in single-user toilet rooms with in-swinging doors; stairs; elevators; location of accessible routes to stages; accessible attorney areas and witness stands...
-
Tips for Weighing People Using an Accessible Scale
You should use an accessible scale with people who… Have difficulty standing or maintaining balance on a standard scale platform....
-
M101.2 Application (Section-by-Section Analysis)
In the NPRM the Access Board proposed that the MDE Standards would be applied to diagnostic equipment based on the patient position the equipment is designed to support....
-
M305.2.2 Length
The length of transfer supports shall comply with M305.2.2.1 or M305.2.2.2....
-
11B-602.7 Drinking fountains for standing persons
Spout outlets of drinking fountains for standing persons shall be 38 inches (965 mm) minimum and 43 inches (1092 mm) maximum above the finish floor or ground....
-
11B-602.7 Drinking fountains for standing persons
Spout outlets of drinking fountains for standing persons shall be 38 inches (965 mm) minimum and 43 inches (1092 mm) maximum above the finish floor or ground....
-
Sec.36.308(a)(3)
(3) The requirements of paragraph (a) of this section shall not be interpreted to exceed the standards for alterations in subpart D of this part.
-
M305.2.3 Height (Section-by-Section Analysis)
The MDE Advisory Committee supported adding a requirement setting the height of transfer supports within the range described in question 20 in the MDE NPRM preamble, of 6 inches minimum...
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports....
-
Murdock Manufacturing Grab Bars
Grab bars are designed to support a load of at least 250 pounds (113.4 kilogram) grab bars at 33 inch (83.82 cm) above floor or in accordance with local accessibilty regulations....
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the transfer...
-
Bradley Grab Bars 1 1/2" with Concealed Mounting 812
Intermediate supports are contour cut and joined by welding to form an integral part of the grab bar. All exposed welds ground and polished to blend....
-
M305.2.6 Gripping Surface
Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
M305.2.3 Fittings
Transfer supports shall not rotate within their fittings....
-
M305.2.8 Fittings
Transfer supports shall not rotate within their fittings when in place for transfer....
