(1) Design load. Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26...
Search Results "Rail Crossing"
Filters
Commonly Searched Documents
-
§ 38.95(c)(1) Design load
-
§ 38.125(d) Seating
(d) Seating—
-
§ 38.95(b)(3) Emergency operation
(3) Emergency operation. The lift shall incorporate an emergency method of deploying, lowering to ground or platform level with a lift occupant, and raising and stowing the empty...
-
§ 38.123(a)(2)
(2) The height of the water closet shall be 17 inches to 19 inches measured to the top of the toilet seat. Seats shall not be sprung to return to a lifted position.
-
§ 38.95(c)(7) Stowage
(7) Stowage. A compartment, securement system, or other appropriate method shall be provided to ensure that stowed ramps or bridge plates, including portable ramps or bridge plates...
-
§ 38.95(b)(1) Design load
(1) Design load. The design load of the lift shall be at least 600 pounds. Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift...
-
§ 38.95(b)(2) Controls
(2) Controls—
-
§ 38.99 Floors, steps and thresholds
[See subsections ...]
-
§ 38.99(a)
(a) Floor surfaces on aisles, step treads, places for standees, and areas where wheelchair and mobility aid users are to be accommodated shall be slip-resistant
-
§ 38.113(a) Clear width
(a) Clear width.
-
§ 38.113(b) Passageway
(b) Passageway. Doorways required to be accessible by paragraph (a) of this section shall permit access by persons using mobility aids and shall have an unobstructed passageway at...
-
§ 38.75(b)
(b) Where designated wheelchair or mobility aid seating locations are provided, signs shall indicate the location and advise other passengers of the need to permit wheelchair and...
-
§ 38.75 Priority seating signs
[See subsections ...]
-
§ 38.95(b)(11) Boarding direction
(11) Boarding direction. The lift shall permit both inboard and outboard facing of wheelchairs and mobility aids.
-
§ 37.103 Purchase or lease of new non-rail vehicles by private entities primarily engaged in the business of transporting people
[56 FR 45621, Sept. 6, 1991, as amended at 76 FR 57936, Sept. 19, 2011]
-
H. Chapter 7: Communication Features
Chapter 7 in the 2016 Non-Rail Vehicle Guidelines establishes technical requirements for characters on signs, the International Symbol of Accessibility, and vehicular announcement systems...
-
406.5 Location
Curb ramps at marked crossings shall be wholly contained within the markings, excluding any flared sides....
-
D. Chapter 3: Building Blocks
Chapter 3 in the 2016 Non-Rail Vehicle Guidelines has been significantly reorganized from the proposed rule....
-
1. Transfer Supports
specifications to the requirements for location (M305.2.1) and length (M305.2.2) based on the type of transfer support required; has added new technical requirements for height (M305.2.3), cross...
-
1. Sloped Surfaces
Cross slope is the slope or grade of a surface perpendicular to the running slope. The most cross slope allowed on an accessible route is 1:50 (2% or 1.15 degrees)....
-
11B-406.5.10 Diagonal curb ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
-
Issue 2: Location relative to the crosswalk
Issue 2: Location relative to the crosswalk An APS that is mounted outside the crosswalk area may provide misleading information about the crossing location....
-
T603 Wheelchair Securement Systems
The technical requirements in the 2016 Non-Rail Vehicle Guidelines for wheelchair securement systems include provisions on orientation, design load, movement, and rear-facing wheelchair...
-
§ 38.125(b)(13) Handrails
The handrails shall be capable of withstanding a force of 100 pounds concentrated at any point on the handrail without permanent deformation of the rail or its supporting structure....