Over two million people in the United States use a wheelchair for mobility. These Americans not only rely on their assistive technology to complete simple, daily tasks, but they also...
Search Results "Practice Teeing Ground"
Filters
Commonly Searched Documents
-
Executive Summary
-
Development of Surface Roughness Standards for Pathways Used by Wheelchair Users: Final Report
Development of Surface Roughness Standards for Pathways Used by Wheelchair Users: Final Report December 2014 Human Engineering Research Laboratories VA Pittsburgh...
-
3.2.3 Surface
The ground surface in all camp living areas shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
Surface: ADA Standard Section 810.2.1
Bus stop boarding and alighting areas shall have a firm, stable surface.
-
11B-810.2.1 Surface
Bus stop boarding and alighting areas shall have a firm, stable surface.
-
11B-308.2.2 Obstructed high reach
Where a high forward reach is over an obstruction, the clear floor space shall extend beneath the element for a distance not less than the required reach depth over the obstruction....
-
1019.1 General
When an entity determines that any of the following conditions does not permit full compliance with the provision, compliance is required to the extent practicable: Compliance is...
-
1011.2.3 Slope
This section requires the slope of the clear ground space to not be steeper than 1:48 in any direction....
-
Surface and Size [§305.2 and §305.3]
Surface and Size [§305.2 and §305.3] Clear floor spaces must meet requirements for ground and floor surfaces, including criteria for firmness, stability, and slip resistance....
-
1011.2.3 Slope
The slope of the clear ground space surface shall not be steeper than 1:48 in any direction....
-
1011.2.3 Slope
The slope of the clear ground space surface shall not be steeper than 1:48 in any direction....
-
4.6.7 Openings
Openings in the clear floor or ground space surface shall not allow passage of a sphere more than 1/2 inch (13 mm) diameter....
-
III-4.2100 General
A public accommodation must reasonably modify its policies, practices, or procedures to avoid discrimination....
-
4.3.3 Slope
When the surface is not paved or is not elevated above the natural ground, slopes not steeper than 1:33 (3 percent) shall be permitted where necessary for drainage. ...
-
Acceptable Trail Surfacing Requirements
We also needed to consider several practical aspects for processing the SEWF material and maintaining a safe work environment....
-
Accessible Miniature Golf Course Holes
Sections 239.2 and 1007.3 of the 2010 Standards require at least fifty percent (50%) of golf holes on miniature golf courses to be accessible, including providing a clear floor or ground...
-
4.2.4.1 Size and Approach
The minimum clear floor or ground space required to accommodate a single, stationary wheelchair and occupant is 30 in by 48 in (760 mm by 1220 mm) (see Fig. 4(a))....
-
305.5 Position
Unless otherwise specified, clear floor or ground space shall be positioned for either forward or parallel approach to an element....
-
11B-305.5 Position
Unless otherwise specified, clear floor or ground space shall be positioned for either forward or parallel approach to an element....
-
Section 2. Covered multifamily dwellings
dwellings" or "covered multifamily dwellings subject to the Fair Housing Amendments" means buildings consisting of four or more dwelling units if such buildings have one or more elevators; and ground...
-
Standards that exclude an entire class of individuals with disabilities
Standards that exclude an entire class of individuals with disabilities "Blanket" exclusions of this kind usually have been established because employers believed them to be...
-
§100.50(b)
(b) It shall be unlawful to:
-
1.1.17 Stairs
1.1.17 Stairs. Measure cast - in - place stairs for both riser height and tread depth of each riser and tread. For stairs 60 in. (1520 mm) or less in width, measure along a line...
-
1.1.9 Horizontal gaps and vertical alignment
1.1.9 Horizontal gaps and vertical alignment. Measure for local horizontal discontinuities and variations in vertical alignment such as at concrete joints, gaps, grade breaks, and at...