Common Requirements (R304.5) (Section-by-Section Analysis) The clear width of curb ramp runs (excluding flared sides), blended transitions, and turning spaces must be 1.2 meters (4 feet...
Search Results "Flared Side"
Filters
Commonly Searched Documents
-
Common Requirements (R304.5) (Section-by-Section Analysis)
-
Attachment I
The toilet centerline is 16½ inches from the side wall. Provide a toilet with a centerline that measures 18 inches from the near side wall. ...
-
AJW Architectural Products US888 Single Security Toilet Tissue Dispenser, Exposed Mounting - Surface Mounted - Non-Controlled
One end of tube is flared the other end has two holes drilled (5/16â€) to accommodate keyed pad-lock (pad-lock & key not provided)....
-
Mockett DH2 Door Handle Installation
Installation guide for the DH2 Door Handle, including Single-Sided and Back to Back Mounting installations. ...
-
11B-405.9 Edge protection
Edge protection complying with Section 11B-405.9.2 shall be provided on each side of ramp runs and at each side of ramp landings. [2010 ADA Standards] 405.9 Edge Protection....
-
R305 Detectable Warning Surfaces (Section-by-Section Analysis)
At curb ramps and blended transitions, detectable warning surfaces must extend the full width of the ramp run (excluding flared sides), blended transition, or turning space....
-
Edge Protection: ADA Standard Section 405.9
Section 405.9 covers the current ADA Standards for edge protection at ramps.
-
Where Required: ADA Standard Section 505.2
Section 505.2 covers the current ADA Standards for where handrails are required.
-
Doors: ADA Standard Section 604.8.1.2
Section 604.8.1.2 covers the current ADA Standards for wheelchair accessible compartment doors.
-
Swinging Doors and Gates: ADA Standard Section 404.2.4.1
Section 404.2.4.1 covers the current ADA Standards for maneuvering clearances at swinging doors and gates.
-
11B-806.2.3 Sleeping areas
At least one sleeping area shall provide a 36 inch (914 mm) by 48 inch (1219 mm) minimum clear space on both sides of a bed....
-
11B-813.2.1.2 Clearance
A 36 inches minimum (914 mm) width side clearance shall be provided along the entire length of one side of adult changing tables....
-
11B-604.8.2.2 Doors
side of the compartment and any obstruction shall be 44 inches (1118 mm) minimum....
-
11B-502.3.4 Location
Access aisles shall be permitted to be placed on either side of the parking space except for van parking spaces which shall have access aisles located on the passenger side of the parking...
-
11B-404.2.4.1 Swinging doors and gates
CLEARANCES AT MANUAL SWINGING DOORS AND GATES TYPE OF USE MINIMUM MANEUVERING CLEARANCE Approach direction Door or gate side...
-
At your service. A 20 minute film. Engage customers with disabilities.
The Mid-Atlantic ADA Center has partnered with Storyline Motion Pictures (filmmakers of the critically acclaimed PBS documentary Lives Worth Living, and curators of the Disability...
-
11B-604.2 Location
The water closet shall be positioned with a wall or partition to the rear and to one side....
-
11B-805.2.2 Beds
A 36 inch (914 mm) minimum wide clear space shall be provided along the full length of each side of the beds. [2010 ADA Standards] 805.3 Clear Floor or Ground Space....
-
1015.2 Where required
vertically to the floor or grade below at any point within 36 inches (914 mm) horizontally to the edge of the open side....
-
Grab Bars: ADA Standard Section 604.8.2.3
Section 604.8.2.3 covers the current ADA Standards for grab bars in ambulatory accessible compartments.
-
Clearance: ADA Standard Section 608.2.2.1
Section 608.2.2.1 covers the current ADA Standards for the clearances of standard roll-in type shower compartments.
-
Cubicles and Counters: ADA Standard Section 231.4.1
Section 231.4.1 covers scoping requirements in the current ADA Standards for cubicles and counters.
-
Sleeping Areas: ADA Standard Section 806.2.3
At least one sleeping area shall provide a clear floor space complying with 305 on both sides of a bed....
