The requirements for stair and ramp handrails in this document are for adults....
Search Results "Adult Dimension"
-
11B-505.4 Height
-
4.20.2 Floor Space
However, because frail older adults do not perform sliding transfers, clear floor space in eldercare facilities was needed for one or more caregivers to be able to assist with getting in...
-
505.4 Height
The requirements for stair and ramp handrails in this document are for adults....
-
232.2 General Holding Cells and General Housing Cells
., male/female and adult/juvenile) to facilitate access....
-
AssistiveWare Keeble Accessible Keyboard
Accessible keyboard for iOS Keeble allows students and adults with physical or vision impairments to type in almost any app....
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
11B-407.4.7.2 Keypads
The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 11B-703.3.1 _|Braille Dimensions|_....
-
11B-302.3 Openings
Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel....
-
1. Measuring Tape
You will generally not need to measure dimensions in increments of less than ¼ inch....
-
5.4.2.1 Transfer Support Length Recommendation for Stretchers
5.4.2.1 Transfer Support Length Recommendation for Stretchers On Stretchers, the transfer surface is oriented along the long dimension of the surface on which patients are positioned...
-
5.4.4.2 Transfer Support Distance from Transfer Surface Recommendation for Imaging Equipment
Rationale for the Recommendation The Committee decided to follow the recommended 1 1/2inch proposal but included a 3-inch dimension to accommodate movement of the support....
-
Openings in Beach Access Routes
Place elongated openings more than a quarter of an inch wide with the long dimension perpendicular or diagonal to the primary direction of travel (see figure 44)....
-
Openings in Outdoor Recreation Access Route Surfaces
Place elongated openings that are more than a quarter of an inch wide with the long dimension perpendicular or diagonal to the primary direction of travel (figure 44)....
-
Knee Clearance: Clearance as Measured from Anterior-Most Point - Manual Wheelchair
It references dimensions of clearance height and depth to the forward-most point on the person or mobility device (e.g., toe, footrest)....
-
Knee Clearance: Clearance as Measured from Dorsal Foot Point - Manual Wheelchair
It references dimensions of clearance height and depth to the dorsal foot point on a person (e.g., top of ankle)....
-
1.2.1
1.2.1 Use the plus - or - minus symbol (±) after a dimension when it must be made clear what the expected tolerance is. This should be coordinated with the specification requirements....
-
11B-407.4.7.2 Keypads
The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 11B-703.3.1 _|Braille Dimensions|_....
-
11B-903.4 Back support
The bench shall provide for back support or shall be affixed to a wall along its long dimension....
-
11B-903.4 Back support
The bench shall provide for back support or shall be affixed to a wall along its long dimension....
-
Background
For example, Sanford, et al. have previously reported (1995, 1999) that the preferred ADA toilet configuration does not work as well as it should for the majority of older adults, including...
-
Urinal Depth
In the proposed rule, the Board sought to clarify the requirement in the original ADAAG that accessible urinals have an "elongated" rim by specifying a minimum dimension of 13 ½ inches,...
-
5.2.1.4 Transfer Surface Size for Imaging Equipment
The transfer surface should be located such that the long dimension of 28 inches is located parallel to the patient scanning/imaging side of the table....
-
407.12.3.1 Unobstructed Forward Reach (Section-by-Section Analysis)
These dimensions and their resulting geometry are consistent with the ADA and ABA Accessibility Guidelines (36 CFR Part 1191, Appendix D, sections 306 and 308)....
-
4.10.3 Hall Call Buttons
Call buttons shall be a minimum of 3/4 in (19 mm) in the smallest dimension. The button designating the up direction shall be on top. (See Fig. 20.) Buttons shall be raised or flush....
