Section 205.1 of the ADA Standards covers information on scoping requirements for operable parts in the most current ADA Standards.
Search Results "Clear Ground Space"
-
General: ADA Standard Section 205.1
-
11B-201.1 Scope, 11B-201.2 Application based on building or facility use, 11B-202.2 Additions, 11B-202.3 Alterations
These would then constitute an altered space....
-
Xpress II Inclined Platform Wheelchair Lift
When the platform is not in use it is folded, taking up minimal space on the stairway. The Xpress II is cost-effective and is ADA compliant....
-
Pressalit Care VALUE Support Arm Fixed Height Swing Grab Bar with Leg
The support arm can fold up when not in use or to make more space. Maximum Vertical Load: 297Lbs.(135kg)...
-
Kompan, Inc. Multi-sport Game Courts Freegame Court FRE2110
With facilities and all-round visibility that allow the users to feel safe, FREEGAME creates true ‘living space’ for all age groups....
-
3.6 Youngstown Tinseltown 7, 7401 Market Street, Boardman, Ohio
3.6 Youngstown Tinseltown 7 7401 Market Street, Boardman, Ohio - In Auditorium 3, the four (4) wheelchair spaces shall be relocated one row farther back in the auditorium from their...
-
3.11 Tinseltown, 651 Medford Center, Medford, Oregon
3.11 Tinseltown 651 Medford Center, Medford, Oregon - In Auditorium 6, the four (4) wheelchair spaces shall be located one row further back in the auditorium from their current location...
-
Start Outside
If there is a parking lot or garage check for the correct number of accessible parking spaces, including van-accessible spaces....
-
5.1 GENERAL
Where practical, accessible tables should be distributed throughout the space or facility....
-
GET@>> https://www.facebook.com/EpiCoolerPortableACUnitedKingdom/
EpiCooler Portable AC United Kingdom Marketed as a compact, energy-efficient, and no-installation cooling device, EpiCooler claims to provide quick cooling and heating for small indoor spaces...
-
T504.1 General
Passenger access routes shall provide clearances that are sufficient to permit passengers using wheelchairs to move between wheelchair spaces and doorways that provide accessible boarding...
-
Side Approach
Sinks located in corners may not be fully within reach and the space to the rear of the side approach space cannot be reached....
-
608.2.2 Standard Roll-In Type Shower Compartments
Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-406.6 Islands
The clear width of the accessible route at islands shall be 60 inches (1524 mm) wide minimum. Where curb ramps are provided, they shall comply with Section 11B-406....
-
Security Bollards [7.4] and Security Devices
Security Bollards [7.4] and Security Devices Bollards and rails used to keep shopping carts on the premises must allow an accessible clear passage (32 inches wide minimum) along at least...
-
4.8.4 LANDINGS
(2) The landing length shall be a minimum of 60 in (1525 mm) clear....
-
Rebuilding Together Richmond - Richmond, VA
We serve nearly 100 homeowners each year and impact hundreds more with our community space projects, thanks to the help of our 1,000+ volunteers and skilled laborers....
-
11B-805.7 Built-in cabinets and work surfaces
A 30-inch by 48-inch clear floor space, in compliance with Section 11B-305, shall be centered in front of the display screen....
-
106 Definitions
removed as unnecessary, in most cases due to changes in certain scoping or technical requirements: "accessible route," "area of refuge," "automatic door," "destination-oriented elevator," "ground...
-
A4.3.1(1) Travel Distances
This assumes a rate of about 1.5 ft/s (455 mm/s) on level ground. It also assumes that the traveler would move continuously....
-
1132A.9 Smooth surface
Swinging door or gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
