Several user types, including bicycles, recumbent bicycles, and hand cycles, required more than 3 m (10 ft) of width (at the 85th percentile level) to execute a three-point turn....
Search Results "Turning T"
Commonly Searched Documents
-
Path Width
-
Literature Cited
Laufenberg T., Krzysik, A. M., and Winandy, J....
- GE® 24" Standard Clean Free-Standing Electric Range JAS02SNSS
-
R304.5.1.2 Shared Use Paths
As proposed in the NPRM, R304.5.1 would require the clear width of curb ramp runs (excluding flared sides), blended transitions, and turning spaces to be 4 feet minimum....
-
Water Play Components
If the surface of the accessible route, clear floor or ground spaces, and turning spaces that connect play components are submerged, the accessible route does not have to comply with the...
-
11B-705.1.2.2.2 Parallel curb ramps
Detectable warnings shall extend the full width of the turning space at the demarcation between the street and the sidewalk less 2 inches (sic) (51 mm) maximum on each side....
-
Volume Control Telephones: ADA Standard Section 704.3
If the microphone in the handset is not being used, a mute button that temporarily turns off the microphone can also reduce the amount of background noise which the person hears in the earpiece...
- TownSteel CDC-110 Classroom Instruder Mechanical Cylindrical
- Cal-Royal JHIL Series Interconnected Lockset
-
R304.2.2 Running Slope
The running slope of the turning space shall be 2 percent maximum....
-
4.1.6(1)(d)
For example, if the elevators and stairs in a building are being altered and the elevators are, in turn, being made accessible, then no accessibility modifications are required to the stairs...
-
4.16.2 Clear Floor Space
However, in accommodating assisted transfers, these guidelines were less of an issue than providing space adjacent to the water closet for caregivers and including a 5’ turning radius in...
-
Comparison of Single-User Toilet Room Layouts: 1A, 1B, and 1C
The size of this space is determined by the minimum width required for the water closet and lavatory between the side walls, the minimum wheelchair turning space, and the space required...
-
Continuous Width (R302.3) (Section-by-Section Analysis)
A minimum width of 1.2 meters (4 feet) will accommodate turns at intersections and building entrances....
-
Paragraph (d) (Advisory Guidance)
For the use of voice carry-over, where the person can speak but not hear, the user needs to be able to turn the microphone on to speak and off to allow them to receive the TTY text replies...
-
Clear Tread Width and Passing Spaces for Outdoor Recreation Access Routes
Another option allows a T-intersection of two outdoor recreation access routes or other walking surfaces to be a passing space (figure 42) provided that the arms and stem of the T-shaped...
-
Paragraph (b) (Advisory Guidance)
hearing aid, they may directly connect their hearing aid to the audio signal or plug in a small audio loop which allows them to couple the audio signal through their hearing aid's built-in T-coil...
-
Common Problems with Entrances and Doors
Ø Round doorknob hardware prevents someone who cannot grasp or turn a doorknob from entering....
-
Specific areas of dispute. (Section-by-Section Analysis)
With the exception of swimming pools, which are discussed below in § 36.304(d)(4)(ii), these concerns are addressed, in turn, in the following paragraphs....
-
N. Health Units/Medical Care Areas
should be on an accessible route and have accessible features, including an accessible entrance, an accessible route to the different types of services offered within the medical care unit, turning...
-
M9
No Notes: 1. 48-inch minimum by 66-inch minimum clear floor space for toilet 2. 48-inch minimum by 30-inch minimum clear floor space for lavatory 3. 60-inch minimum turning...
-
Floor and Ground Surfaces
walking surfaces, ramps, elevators, and lifts stairways that are part of a means of egress required clearances, including clear floor space, wheelchair seating spaces, turning...
-
ASTM: ADA Standard Section 105.2.3
Section 105.2.3 of the ADA Standards cover references to the American Society for Testing and Materials (ASTM) standards.