The 95th percentile value for female users of manual and power wheelchairs was approximately 30.5 in. and would provide adequate clearance depth such that approximately 95% of female users...
Search Results "Wheelchair Space (Recreation)"
Commonly Searched Documents
-
Conclusions
-
1008.3 Transfer Systems
Designers should minimize the distance between the points where a child transfers from a wheelchair or mobility device and where the elevated play components are located....
-
41. May an employer ask whether a reasonable accommodation is needed when an employee with a disability has not asked for one?
Or, if an employer is scheduling a luncheon at a restaurant and is uncertain about what questions it should ask to ensure that the restaurant is accessible for an employee who uses a wheelchair...
-
If the manufacturer states that the design load is 800 pounds, can the transportation operator limit actual use to 600 pounds for safety reasons?
The National Highway Traffic Safety Administration’s (NHTSA) motor vehicle safety regulations require that a wheelchair lift be tested to withstand a 600-pound load....
-
Maximum Extent Feasible
., those who use wheelchairs) would not be feasible, the facility shall be made accessible to persons with other types of disabilities (e.g., those who use crutches, those who have impaired...
-
12184(b)(3)
solicitation is made after the 30th day following the effective date of this section, that is not readily accessible to and usable by individuals with disabilities, including individuals who use wheelchairs...
-
Clear Width [4.13.5] and Vertical Clearance
Panic bars and other hardware do not require additional width since they are usually mounted above the widest portion of wheelchairs....
-
Doors [9.2.2(3), 9.4]
Recommendation: An additional peephole in the door for people who use wheelchairs or who are of short stature is not required but may be desirable especially if one offering a wide angle...
-
Den
Levers on all doors throughout the house FSC certified birdseye and quartersawn maple paneling Zoned heating on thermostats Murphy beds at the height of a wheelchair...
-
Locating Controls & Devices: Percent of People Who Can Reach the Matrix Cell Indicated While Holding No Weight - Forward Approach Scooter
forward reach direction for a given (a) height from the floor (shown the vertical axis) and (b) offset distance (shown on the horizontal axis) from the forward-most point of the person or wheelchair...
-
Carpet [§302.2]
Carpet [§302.2] Carpet that is thick, cushiony, or loose impairs accessibility, particularly wheelchair maneuvering....
-
11B-603.3 Mirrors
In order for mirrors to be usable by people who are ambulatory and people who use wheelchairs, the top edge of mirrors should be 74 inches (1880 mm) minimum from the floor or ground....
-
Curb Ramps
People who use wheelchairs can tip over if they accidentally roll over the non-flared sides. Requirement: 4.7.5 Sides of Curb Ramps....
-
§ 37.43(b)
., those who use wheelchairs) would not be feasible, the facility shall be made accessible to individuals with other types of disabilities (e.g., those who use crutches, those who have impaired...
-
11B-408.1 General
DSA regulates the usability of elevators and platform (wheelchair) lifts for persons with disabilities....
- Pilot Rock: Picnic Table ADA Compliance Comparison
- SCIFIT StepOne Recumbent Stepper
-
II. ENFORCING THE ADA PART 3
to take her wheelchair on its inaccessible vans....
- Pilot Rock PQT3-4 Square Pedestal Table - Expanded or Perforated Steel
- AccessRec DuraDeck 2 Molded Plastic Mat Ground Surface
-
EXPERIENCES OF THE NAMED PLAINTIFFS
Named Plaintiff Conrad Reynoldson has muscular dystrophy and uses an electric wheelchair for mobility....
-
§382.57(c)(7)(i) Visibility
The display screen must be visible from a point located 40 inches (1015 mm) above the center of the clear floor space in front of the automated kiosk....
-
Trailhead
An outdoor space that is designated by an entity responsible for administering or maintaining a trail to serve as an access point to the trail. ...
-
404.2.6 Doors in Series and Gates in Series
The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1220 mm) minimum plus the width of doors or gates swinging into the space....