Bradley Chrome-Plated Double Hook Model 914 Surface-Mounted - Exposed Mounting Chromed-Plated Brass Double Hook...
Search Results "Transfer Surface Height"
-
Bradley Chrome-Plated Double Hook 914
-
TOTO® Drake Two-Piece Toilet, 1.6 GPF, Elongated Bowl
• G-Max® fl ushing system, low consumption (1.6GPF/6.0LPF) • Universal Height • Two-piece design with high-profi le tank • Elongated front bowl and tank set, less seat...
-
Overview
The unique aspects of mammography device design and operation requires components to work when the breast platform is at breast height....
-
4.3 Reach Ranges
They specify maximum and minimum heights but do not take into consideration the fact that the depth and height of the obstruction can vary with a corresponding impact on the reach envelope...
-
Symmetry Vertical Platform Lift VPC-EL
Standard Features: 750 lb capacity Speed: 10 FPM with a 1HP, 115V motor Lifting height: up to 168” Steel constructed with electrostatic, powder-coated finish...
-
Sections 505.10.2 and 505.10.3
Commenters noted that the 2010 Standards will require handrail gripping surfaces with a circular cross section to have an outside diameter of 2 inches, and that this requirement would impose...
-
Q5: Effective Date for Public Entities to Comply
This technical assistance was provided to respond to questions that arose largely due to the development of a variety of road surface treatments, other than traditional road resurfacing,...
-
G. What are Detectable Warnings, Why are They Required, and Where Must They be Provided?
They must be integrated into the walking surface, and there are specific measurements for the size and spacing of the domes.13 What is the function of detectable warnings?...
-
604.7 Dispensers
paper dispensers are installed above the side wall grab bar, the outlet of the toilet paper dispenser must be 48 inches (1220 mm) maximum above the finish floor and the top of the gripping surface...
-
Baby Changing Tables
In addition, convenience fixtures, such as baby changing tables, must be accessible to persons with disabilities under scoping provisions for operable parts (205) and work surfaces (226)...
-
M303.2.2 Width (Section-by-Section Analysis)
an exception in the final rule that permits wheelchair spaces on raised platforms to be 32 inches wide minimum with edge protection no higher than 4 inches, measured from the platform surface...
-
1127B.5, Item 4
A level landing 4 feet (1219 mm) deep shall be provided at the upper end of each curb ramp over its full width to permit safe egress from the ramp surface, or the slope of the fanned or...
-
Technical Memorandum TM 2013-22 Storage (Kitchens and Kitchenettes)
Counter surfaces shall not be considered shelf space nor used to satisfy the requirements of 804.5....
-
1017.4 Passing Spaces
at shorter intervals if the clear tread width is less than 60 inches (1525 mm), where a trail is: --Heavily used; or --A boardwalk or otherwise not at the same level as the ground surface...
-
Implementation Challenges for Interiors (slides 16 and 17)
In the past, [we] have been required to have truncated cones covering the entire surface. For someone in a wheelchair, that is literally hell....
-
Disorienting Spaces (slide 7)
It’s actually a flat surface, and then going into the lovely, also very easy-to-navigate checkerboard flooring pattern....
-
Protruding Objects on Beach Access Routes
as signs that extend into the clear width area of a beach access route or resting interval and are between 27 inches (685 millimeters) and 80 inches (2,030 millimeters) above the travel surface...
-
1017.4 Passing Spaces
at shorter intervals if the clear tread width is less than 60 inches (1525 mm), where a trail is: • Heavily used; or • A boardwalk or otherwise not at the same level as the ground surface...
-
Beach Access Routes
Beach access routes provide a firm and stable surface over the sand and are used by beach visitors with and without disabilities....
-
Construction Specification Institute
Construction Specification Institute While developing suggested tolerances for surface materials, the Construction Specifications Institute developed a suggested method for measuring ramp...
-
1.1.1
The simplest way for design professionals to avoid problems with construction tolerances related to surface accessibility and other accessible elements is to design for slopes and dimensions...
-
11B-703.7.2.6.3 Unisex toilet and bathing facilities
The color of the circle symbol shall contrast with the color of the door or surface on which the combined circle and triangle symbol is mounted, either light on a dark background or dark...
-
American Specialties Omara Collection Spare Toilet Paper Roll Holder 7316
All exposed surfaces have a satin finish....
-
Bradley Adjustable Tilt Mirror 782
Model 782 Series Satin finish Stainless Steel Frame Adjustable Tilt Mounting Welded Corners Alternate reflective surfaces available...
