(2) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with FAA safety requirements...
Search Results "Access Aisle Width"
Filters
Commonly Searched Documents
-
§382.133(e)(2)
-
Technical Requirements
Technical Requirements—Specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
11B-505.2.1 Orientation
The orientation of at least one handrail shall be in the direction of the stair run, perpendicular to the direction of the stair nosing, and shall not reduce the minimum required width of...
-
11B-705.1.2.6 Reflecting pools
When detectable warnings are provided at reflecting pools, it shall be 24 inches (610 mm) minimum and 36 inches (914 mm) maximum in width....
-
11B-505.2.1 Orientation
The orientation of at least one handrail shall be in the direction of the stair run, perpendicular to the direction of the stair nosing, and shall not reduce the minimum required width of...
-
Summary
Summary The following report provides a brief analysis of four anthropometric dimensions which were considered relevant to the width and depth dimensions of a seating surface for wheeled...
-
Clearance in Base (M301.4.1 and M302.4.1)
Where the width of the examination surface is less than 36 inches, the clearance depth would be required to extend the full width of the equipment....
-
Minimum Rear Wall Required.
It appears that this comment references the 2010 ADA Standards for Accessible Design for minimum bench length (42") but uses the CA - 2013 minimum bench length (48") to develop the minimum...
-
Sections 505.10.2 and 505.10.3
The requirement in the 1991 Standards that handrails extend horizontally at least 12 inches beyond the width of one tread at the bottom of a stair was changed in the 2004 ADAAG by the Access...
-
5.3.2 Transfer Sides Recommendations for M301
Locating the transfer surface at a corner of the equipment and providing unobstructed access to the two transfer sides also would facilitate assisted transfers....
-
Access Center for Independent Living (ACIL) - Dayton, OH
The Access Center for Independent Living is one of 12 Centers for Independent Living in Ohio....
-
Visually IMpaired Accessible Keypad Door Lock
Ran into an interesting issue in a claim by a visually impaired plaintiff The claim was that the push button keypad was not accessible for a visually impaired person - see attached photo...
-
H.6 - Do Federal agency software or web development tools have to meet the Access Board's standards?
Software applications, such as web development tools, are considered EIT and therefore covered by the Access Board's standards, unless an exception applies....
-
5.3.3 Transfer Sides Recommendations for M302
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface....
-
Floor Plan of Elevator Cars [4.10.9]
The car dimensions specified in ADAAG are based on earlier accessibility guidelines developed in accord with industry standards....
-
1133A.2.1, Item 3
All other kitchen designs shall provide a minimum clear width of at least 48 inches (1219 mm). (See Figure 11A-10A)....
-
Parking Spaces for Vehicles Other Than RVs [F244.2.3.2.2]
Parking spaces for vehicles other than RVs within camping units with mobility features must comply with the following technical requirements for width, surface, and slope....
-
T702.3 Character Proportions
Characters shall use fonts where the width of the uppercase letter “O” is 55 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
Egress Stairs
The requirement for a minimum 48 inch width between handrails is specific to stairs adjacent to areas of rescue assistance and does not apply generally to stairs covered by 4.9....
-
1133A.2.1, Item 3
All other kitchen designs shall provide a minimum clear width of at least 48 inches (1219 mm). (See Figure 11A-10A)....
-
11B-813.2.1.1 Size
Adult changing tables shall have a changing surface of 70 inches (1778 mm) minimum length and 30 inches (762 mm) minimum width....
-
ATA - Alliance for Technology Access
The mission of the ATA is to increase the use of technology by children and adults with disabilities and functional limitations. ATA encourages and facilitates the empowerment of...
-
Tactile Design for Universal Access
Touch Graphics, Inc. was established in 1997 to refine and commercialize methods for tactile graphics production that were first demonstrated by Karen Luxton Gourgey and the Computer...
-
5.2.1 Transfer Surface Size Recommendations for M301
The technical criteria do not address the overall width and depth of patient support surfaces because of the diverse shape and size of these surfaces....
