[2010 ADAS] 224.1.2 Guest Room Doors and Doorways. ...
Search Results "ADA Standard"
-
11B-224.1.2 Guest room doors and doorways
-
11B-903.4 Back support
[2010 ADAS] 903.4 Back Support. The bench shall provide for back support or shall be affixed to a wall....
-
II-2.1000 General
Title II of the ADA prohibits discrimination against any "qualified individual with a disability."...
-
Accessible Means of Entry to Spas
Sections 242.4 and 1009.2, 1009.4, and 1009.5 of the 2010 Standards require spas to meet accessibility requirements, including an accessible means of entry....
-
Mirror Height
The ANSI A117.1‒2003 standard contains a new requirement that specifies a height of 35 inches maximum for accessible mirrors not located above a lavatory or counter top....
-
§ 1194.23(j)
(j) Products that transmit or conduct information or communication, shall pass through cross-manufacturer, non-proprietary, industry-standard codes, translation protocols, formats or other...
-
5. WAIVERS
Any other deviation from these DoD Standards shall be made only through the waiver or modification process....
-
E101.4 Units of Measurement (Section-by-Section Analysis)
This proposed section is new to the 508 Standards and would clarify dimensions stated in the text of the proposed rule....
-
E202.3 Federal Contracts
ICT acquired by a contractor incidental to a contract shall not be required to conform to the 508 Standards. Advisory E202.3 Federal Contracts....
-
Question 1
The Department is considering adopting the Access Board's standards for medical diagnostic equipment....
-
Dispersion
Dispersion Recommendation: Wheelchair accessible units and standard units should be evenly dispersed to maximize convenient availability....
-
Drinking Fountains and Water Coolers [4.15]
Units that meet conventional industry standards are acceptable for providing access to people who have difficulty bending or stooping....
-
Salad Bars and Buffet Counters
Salad Bars and Buffet Counters Recommendations: The standard reach range should be considered in the design of built-in salad bars although not all portions are required to be within...
-
Surface Smoothness
The standards limit changes in level and openings in floor and ground surfaces, but they do not further address overall surface smoothness....
-
Disproportionality (20%)
Regulations implementing the standards define “disproportionate” as exceeding 20% of the total cost of alterations to the primary function area....
-
§ 35.150(b)(4) Swimming pools, wading pools, and spas
The requirements set forth in sections 242 and 1009 of the 2010 Standards shall not apply until January 31, 2013, if a public entity chooses to make structural changes to existing swimming...
-
68.101(b) Lease Evaluation Form
If a Lease Evaluation Form is not submitted, compliance with all applicable standards shall be required....
-
Regulatory Flexibility Act: Initial Regulatory Flexibility Analysis
The proposed standards do not impose any mandatory requirements on any entity, including small entities....
-
8. Boarding Separately From Wheelchair
(Note, however, that under § 37.165(b), entities are required to accommodate device/user loads and dimensions that exceed the former “common wheelchair” standard, as long as the vehicle...
-
8. Boarding Separately From Wheelchair
(Note, however, that under §37.165(b), entities are required to accommodate device/user loads and dimensions that exceed the former “common wheelchair” standard, as long as the vehicle and...
-
1.1.4 Appendices
code shall not apply unless specifically adopted by a state agency or adopted by a local enforcing agency in compliance with Health and Safety Code Section 18901 et. seq. for Building Standards...
-
11B-1008.2.6 Ground surfaces
Ground surfaces must be inspected and maintained regularly to ensure continued compliance with the ASTM F 1951 standard....
-
1.1.4 Appendices
code shall not apply unless specifically adopted by a state agency or adopted by a local enforcing agency in compliance with Health and Safety Code Section 18901 et. seq. for Building Standards...
-
1008.2.6 Ground Surfaces
Ground surfaces must be inspected and maintained regularly to ensure continued compliance with the ASTM F 1951 standard....