When the surface of tent pads, tent platforms, and clear ground spaces is constructed of materials other than asphalt, concrete, or boards, the surface must be no steeper than 1:48 (2 percent...
Search Results "Firm Surface"
Filters
Commonly Searched Documents
-
Slope [1013.3]
-
11B-403.6 Handrails
Where handrails are provided along walking surfaces with running slopes not steeper than 1:20 they shall comply with Section 11B-505. Advisory 11B-403.6 Handrails....
-
Stabilizer Solutions StaLok Stabilizer Joint Sand
It is firm enough that you can power wash it when dry. After water begins to collect during a storm, StaLok Paver Sand acts like a sponge....
-
M302.2 Transfer Surface
A transfer surface shall be provided and shall comply with M302.2....
-
M302.2 Transfer Surface
A transfer surface shall be provided and shall comply with M302.2....
-
408.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
408.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
606.5 Exposed Pipes and Surfaces
There shall be no sharp or abrasive surfaces under lavatories and sinks...
-
Handrails Requirement
The handrail requirements in section 505 address specifications for continuity, height, clearance, gripping surface, cross section, fittings, and extensions....
-
Other international standards
Australian NATSPEC Reference Volume 1: Building Works, Concrete Finishes Section Three classes of surface finish based on using a straightedge method of testing: Class A...
-
804.3 Kitchen Work Surface
In residential dwelling units required to comply with 809, at least one 30 inches (760 mm) wide minimum section of counter shall provide a kitchen work surface that complies with 804.3....
-
804.3 Kitchen Work Surface
In residential dwelling units required to comply with 809, at least one 30 inches (760 mm) wide minimum section of counter shall provide a kitchen work surface that complies with 804.3....
-
606.5 Exposed Pipes and Surfaces
There shall be no sharp or abrasive surfaces under lavatories and sinks. [ECTCR UFAS 4.19.4, 4.24.6, 4.34.6.5(8)]...
-
Figure 302.3 Elongated Openings in Floor or Ground Surfaces – Drawing from the U.S. Access Board
-
1.1.3
1.1.3 A maximum overall design running slope for exterior accessible surfaces (other than ramps), such as sidewalks, of 4% (approximately 1:25) is recommended....
-
17. Can broken or older ground level play components be replaced without changing the surface?
Can broken or older ground level play components be replaced without changing the surface? Yes....
-
11B-606.5 Exposed pipes and surfaces
11B-606.5 Exposed pipes and surfaces. Water supply and drain pipes under lavatories and sinks shall be insulated or otherwise configured to protect against contact....
-
RecGrass Synthetic Grass Ground Surface System Section
Requires the Premium User plan or above. (Login or upgrade your account!) -
Sargent NB8700 Top Latch Surface Vertical Rod Exit Device
Surface Vertical Rod Less Bottom Rod Exit Device is for both rated and non-rated openings....
-
The Dipstick® Floor Profiler Tool
Calculates F-numbers for runs, sections, and surfaces on site Instantly produces profile graphs on site "Instant" downloading to desktop or laptop computer Automatic zeroing Prints...
-
Stable
A surface is not permanently affected by expected weather conditions and can sustain normal wear and tear from the expected use(s) of the area, between planned maintenance....
-
Analysis of Transfer Surface Dimensions Based on Wheeled Mobility User Anthropometry
Access Board RE: Analysis of Transfer Surface Dimensions Based on Wheeled Mobility User Anthropometry...
-
2) Where the Standard says "Changes in level are not permitted"
permitted", such as 304.2 for turning spaces: Here the standard is followed by an unenforceable advisory that says, "As used in this section, the phrase ‘changes in level’ refers to surfaces...
