Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
Search Results "Shall"
-
11B-1008.2.5.3.1 Handrail gripping surfaces
-
11B-407.4.7.1.1 Type
Control buttons shall be identified by raised characters or symbols, white on a black background, complying with Section 11B-703.2, and Braille complying with Section 11B-703.3....
-
11B-1002.4.7.1 Shoulder-to-shoulder seating
Where an amusement ride provides shoulder-to-shoulder seating, companion seats shall be shoulder-to-shoulder with the adjacent wheelchair space....
-
11B-707.2 Clear floor or ground space
A clear floor or ground space complying with Section 11B-305 shall be provided....
-
1009.4.1 Standby power
The elevator shall meet the emergency operation and signaling device requirements of California Code of Regulations, Title 8, Division 1, Chapter 4, Subchapter 6, Elevator Safety Orders....
-
11B-1002.4.7.1 Shoulder-to-shoulder seating
Where an amusement ride provides shoulder-to-shoulder seating, companion seats shall be shoulder-to-shoulder with the adjacent wheelchair space....
-
11B-215.2 Public and common use areas
Alarms in public use areas and common use areas shall comply with Chapter 9, Section 907.5.2.3.1. [2010 ADA Standards] 215.2 Public and Common Use Areas....
-
11B-212.2 Kitchens, kitchenettes, and wet bars
Kitchens, kitchenettes and wet bars shall comply with Section 11B-804. [2010 ADA Standards] 212.2 Kitchens and Kitchenettes. Kitchens and kitchenettes shall comply with 804....
-
11B-703.8.7 Character spacing
Spacing shall be measured between the two closest points of adjacent low resolution VMS characters within a message, excluding word spaces....
-
11B-703.8.14 Rate of change
Where a VMS message can be displayed in its entirety on a single screen, it shall be displayed on a single screen and shall remain motionless on the screen for a minimum 3 seconds or one...
-
11B-703.7.2.6.4 Edges and vertices on geometric symbols
Edges shall be eased or rounded at 1/16 inch (1.59 mm) minimum, or chamfered at 1/8 inch (3.2 mm) maximum....
-
232.1 General
(1) New construction of jails, prisons, and other detention and correctional facilities shall comply with the 2010 Standards except that public entities shall provide accessible mobility...
-
D. Election Day Compliance Review
The checklist shall include clear instructions and diagrams for the remedial measures to be implemented by the election judge. ...
-
11B-504.4.1 Contrasting stripe
The stripe shall extend the full width of the step or upper approach and shall be of material that is at least as slip resistant as the other treads of the stair....
-
11B-411.2.1.3.2 Touch screen call console arrangement
Where touch screen call consoles are provided, the touch screen shall be located directly above the accessibility function button....
-
11B-406.3.2 Turning space
A turning space 48 inches (1219 mm) minimum by 48 inches (1219 mm) minimum shall be provided at the bottom of the curb ramp....
-
11B-411.2.1.3.1 Keypad call console arrangement
Where keypad call consoles are provided, the display screen shall be located directly above the keypad....
-
M303.2.2 Width
Wheelchair spaces shall be 36 inches (915 mm) wide minimum....
-
11B-703.8.6 Stroke width
The uppercase letter “I” shall be used to determine the allowable stroke width of all low resolution VMS characters of a font....
-
1012.5 Slope
The slope of the surface of parking spaces and pull-up spaces shall not be steeper than 1:48 in any direction....
-
11B-216.13.2 Removal of Cleaner Air Symbol
or facility identified by the Cleaner Air Symbol should temporarily or permanently cease to meet the minimum conditions of use identified in Section 11B-216.13.3, the Cleaner Air Symbol shall...
-
11B-203.13 Raised boxing or wrestling rings
Raised boxing or wrestling rings shall not be required to comply with these requirements or to be on an accessible route....
-
F244.2.3.1 Outdoor Constructed Features
Where provided, at least one of each type of outdoor constructed features shall comply with 1011....
-
1008.2.5.3.1 Handrail Gripping Surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....