Recommended mounting heights for grab bars are 33" - 36" centerline above finished floor. All mounting of grab bars when possible should have in wall mounting back plates....
Search Results "Floor Surface"
-
AJW Architectural Products UG20-Railing UG20X-Y108 108" Concealed Set Screw Flange, 1.25" Diameter, Peened Grip - Configuration Y
-
A. DEFINITIONS AND BACKGROUND
In order to be deemed accessible, a bed must (i) lower to a point no greater than 17-19 inches from the floor, and (ii) be capable of being locked or otherwise fixed into position so as...
-
Notes
ANSI/AAMI HE75 recommends that the height of patient support surfaces "should be easy to adjust (ideally, powered) to suit the needs of health care professionals and patients."...
-
Ascension Virtuoso 5460F Vertical Permanently-Installed Wheelchair Lift
The Ascension Virtuoso 5460F also does not have an access ramp at the lower landing, so patrons can enter the lift directly at floor level....
-
Hoyer Advance-E Power Lift
Whether from the floor or onto a healthcare bed, the Advance operates with ease....
-
Re: Service Counters
The intent of this section of the code is to provide not only an accessible counter surface for the disabled to utilize, but also to allow a free flow interaction with an employee on the...
-
Stanley FBB 269 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
Stanley FBB 266 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
Stanley FBB 268 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
Stanley FBB 264 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
Shared Use Paths: ADA Standard Section 2.
address access to sidewalks, streets, and other pedestrian facilities, provide requirements for pedestrian access routes, including specifications for route width, grade, cross slope, surfaces...
-
11B-609.3 Spacing
Section 11B-609.9 the space between the walls and the grab bar shall be 1½ inches (38 mm) minimum for a distance of 6 inches on either side of the inside corner between two adjacent wall surfaces...
-
11B-609.3 Spacing
Section 11B-609.9 the space between the walls and the grab bar shall be 1½ inches (38 mm) minimum for a distance of 6 inches on either side of the inside corner between two adjacent wall surfaces...
-
11B-705.1.2.3 Islands or cut-through medians
cut-through less 2 inches (51 mm) maximum on each side, placed at the edges of the pedestrian island or cut-through median, and shall be separated by 24 inches (610 mm) minimum of walking surface...
-
404 Doors, Doorways, and Gates
series (404.2.6) clarify the height of door and gate hardware and add an exception for gates at pools, spas, and hot tubs (404.2.7) revise an exception for door and gate surface...
-
Chapter 4: Accessible Routes
Chapter 4 contains technical requirements for accessible routes (402) and the various components of such routes, including walking surfaces (403), doors, doorways and gates (404), ramps...
-
11B-406.5.12 Detectable warnings
width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum measured from the back of the curb on the ramp surface...
-
M303.2.6 Edge Protection (Section-by-Section Analysis)
Protection), the final rule requires platforms with wheelchair spaces that are raised more than 1½ inches in height to provide a minimum 2-inch-high edge protection, measured from the surface...
-
Maximum Slope at Ground Level
A berm may be a natural sloped surface that is present in a hilly play area site, or a ground-level route built with slopes....
-
Amusement Ride Seats Designed for Transfer
When greater distances are required for transfer, consideration should be given to providing gripping surfaces, seat paddings, and avoiding sharp or protruding objects....
-
Tent Pads and Tent Platforms [1013]
Tent pads and tent platforms are defined spaces with prepared surfaces for setting up and securing tents....
-
Curb Ramps and Blended Transitions (R309.4) (Section-by-Section Analysis)
Detectable warning surfaces are not required on curb ramps and blended transitions that connect the access aisle to the sidewalk, including where the sidewalk is at the same level as the...
-
2. Referenced Documents
Guide for Conducting Subjective Pavement Ride Quality Ratings E2133 Standard Test Method for Using a Rolling Inclinometer to Measure Longitudinal and Transverse Profiles of a Traveled Surface...
-
1013.1 General
Tent pads and tent platforms are defined spaces with prepared surfaces for setting up and securing tents....
