No, compliance is not required on both sides of those doors or gates that can be used in one direction only. Compliance is required only on the usable side....
Search Results "Push Side"
Commonly Searched Documents
-
Is compliance on both sides of a door or gate required when it is usable only from one side?
-
Comparison of Single-User Toilet Room “Pairs” With Fixtures Side-by-Side: Plan 2C
Comparison of Single-User Toilet Room “Pairs” With Fixtures Side-by-Side: Plan 2C 2010 Standards Plan-2C Pair: 2010 Standards with In-Swinging Doors...
-
T208.2.2 Doorways on Two Sides of vehicle
Where non-rail vehicles have doorways on two sides, a passenger access route shall connect each wheelchair space to doorways on both sides of the vehicle that provide a means of accessible...
-
DSA IR 16-12: GRAB BAR DESIGN AND CONNECTIONS: 2019 CBC
shall be established in the same manner. 2.3 As an alternate to Section 2.2 above for grab bars spanning 36” or less between supports, a connection using a back-up plate on the other side...
-
M301.2.1 Adjustability
Transfer surfaces shall be adjustable in height measured from the floor to the top of the uncompressed transfer surface and shall provide the following: A. A low transfer position...
-
M301.2.2 Sunset
The low transfer position height, Item A of M301.2.1, shall cease to have effect on [Insert date 5 years after date of publication in the Federal Register].
-
M301.2.2 Sunset Provision (Section-by-Section Analysis)
As discussed in Section IV.B.1.a. (Significant Changes – Transfer Surface Adjustability), this is a new provision that was added to the final rule in conjunction with the new...
- The UpScale Medical Exam Table
- Stable and rock solid. See for yourself!
- Exam Tables & Scales: What Patients Say...
-
Appendix 3 - Comparison of US Standards to IDEA Center Research
Reach 1270 119 1597 1347 1704 Low Side Reach 380...
-
M305.2.5 Surface Hazards
Transfer supports and surfaces adjacent to transfer supports shall be free of sharp or abrasive components and shall have eased edges.
-
M305.2 Transfer Supports
Transfer supports shall comply with M305.2.
-
M305.2 Transfer Supports (Section-by-Section Analysis)
This is an introductory section. As discussed above in Section IV.E.1. (Significant Changes – Transfer Supports), the Access Board strengthened the transfer support requirements and...
-
M305.2.5 Surface Hazards (Section-by-Section Analysis)
The proposed rule did not provide any specific restrictions regarding surface hazards around the transfer supports. No public comments were submitted on this issue, but the MDE...
-
5.4 Transfer Supports
5.4 Transfer Supports.
-
5.4 Transfer Supports Recommendations
5.4 Transfer Supports Recommendations
-
M305.2 Transfer Supports
Transfer supports shall comply with M305.2.
- 609.3 Grab Bar Vertical Clearance
-
11B-804.6.5.1 Side-hinged door ovens
Side-hinged door ovens shall have the work surface required by Section 11B-804.3 positioned adjacent to the latch side of the oven door....
-
11B-804.6.5.1 Side-hinged door ovens
Side-hinged door ovens shall have the work surface required by Section 11B-804.3 positioned adjacent to the latch side of the oven door....
-
11B-804.6.5.1 Side-hinged door ovens
Side-hinged door ovens shall have the work surface required by Section 11B-804.3 positioned adjacent to the latch side of the oven door....
-
T208.2.1 Doorways on One Side of vehicle
Where non-rail vehicles have doorways on one side, a passenger access route shall connect each wheelchair space to a doorway that provides a means of accessible boarding and alighting in...
- Pilot Rock UT Series Side Accessible Picnic Table Using Aluminum