1008.2.4.2 Elevated. The clear width of accessible routes connecting elevated play components shall be 36 inches (915 mm) minimum. EXCEPTIONS: 1....
Search Results "Elevator Hall Signal"
Commonly Searched Documents
-
1008.2.4.2 Elevated
-
Two-way Communication [4.3.11.4]
The two-way communication system must be equipped with both audible signals (for people with vision impairments) and visual signals (for people with hearing impairments) and cannot operate...
-
1009.4.2 Area of refuge
The elevator shall be accessed from an area of refuge complying with Section 1009.6. Exceptions: Areas of refuge are not required at the elevator in open parking garages....
-
1.9.1.2 Application
facilities, as defined, shall be accessible to persons with disabilities as follows: Exception: Certain types of privately funded multistory buildings do not require installation of an elevator...
-
407.3 Elevator Door Requirements
407.3 Elevator Door Requirements. Hoistway and car doors shall comply with 407.3....
-
1003.2.13.3 Elevators
An elevator to be considered part of an accessible means of egress shall comply with the emergency operation and signaling devices requirements of Section 211 of ASME A17.1....
-
Lifts and Elevators
If the voting area is not on the same level as the entrance, there must be an independently operable elevator or lift to provide an accessible route to individuals with disabilities....
-
1008.2.4.2 Elevated
The clear width of accessible routes connecting elevated play components shall be 36 inches (915 mm) minimum. EXCEPTIONS: 1....
-
1008.2.4.2 Elevated
The clear width of accessible routes connecting elevated play components shall be 36 inches (915 mm) minimum. EXCEPTIONS: 1....
-
SENSORY PROVISIONS
., increased amplification, increased signal-to-noise ratio, or combination). For transmitted voice signals, provide a gain adjustable up to a minimum of 20 dB gain....
-
Platform to Hoistway Clearance: ADA Standard Section 407.4.3
Section 407.4.3 covers the current ADA Standards for the required clearance between the elevator car platform and the hoistway landing.
-
Elevators with Standby Power [IBC §1007.4 (2003), §1003.2.13.3 (2000)]
In buildings with four or more stories above or below the level of exit discharge, at least one accessible means of egress must be an elevator with standby power and emergency signaling...
-
General: ADA Standard Section 409.1
Section 409.1 of the ADA Standards covers information in the current ADA Standards for private residence elevators.
-
11B-240.2.2 Elevated play components
Where elevated play components are provided, at least 50 percent shall be on an accessible route and shall comply with Section 11B-1008.4....
-
11B-240.2.2 Elevated play components
Where elevated play components are provided, at least 50 percent shall be on an accessible route and shall comply with Section 11B-1008.4....
-
11B-240.2.2 Elevated play components
Where elevated play components are provided, at least 50 percent shall be on an accessible route and shall comply with Section 11B-1008.4....
-
907.5.2.3 Visible alarms
Visible alarm notification appliances shall not be required in elevator cars....
-
407.4.7 Designations and Indicators of Car Controls
EXCEPTION: In existing elevators, where a new car operating panel complying with 407.4.7 is provided, existing car operating panels shall not be required to comply with 407.4.7....
-
407.4.7 Designations and Indicators of Car Controls
EXCEPTION: In existing elevators, where a new car operating panel complying with 407.4.7 is provided, existing car operating panels shall not be required to comply with 407.4.7....
-
11B-407.4.6.2.3 Illumination
Car control buttons shall be illuminated.
-
11B-411.4.7.4 Button spacing
Button spacing shall comply with Section 11B-407.4.7.1.5.
-
11B-407.4.6.2.4 Operation
Car control buttons shall be activated by a mechanical motion that is detectable.
-
11B-407.4.10.3 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the support rail, fastener, mounting...
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum. Top of support rails shall be 31 inches (787 mm) minimum to 33 inches (838 mm) maximum above...