Laundry machine manufacturers stated that this specification is inconsistent with standard industry design, which allows a 36 inch height....
Search Results "Designed Use"
Filters
Commonly Searched Documents
-
611 Washing Machines and Clothes Dryers
-
Chapter 6 Curb Ramps and Pedestrian Crossings Under Title II of the ADA
What are some common curb ramp designs? Where and when must state and local governments provide accessible curb ramps?...
-
RELIEF TO THE COMPLAINANT
the University shall permanently purge from the Complainant’s transcript any reference to the course from which he had to withdraw during Spring Quarter 2012 (including any “withdrawal” designation...
-
Technical Bulletin: Ground and Floor Surfaces
UNITED STATES ACCESS BOARD A FEDERAL AGENCY COMMITTED TO ACCESSIBLE DESIGN Technical Bulletin: Ground and Floor Surfaces...
-
5.3.3 Transfer Sides Recommendations for M302
This provision will coincide with the seat area design of most examination chairs. NPRM Proposed Provision: M302.2.3 Transfer Sides....
-
Running Slope [1016.7.1]
To accommodate steep terrain, ORARs may be designed with shorter sections that have a steeper running slope and length, as shown in table 3, with resting intervals at the top and bottom...
-
COST OF EQUIPMENT
supports and leg supports 19 inch max. height 28 inch width 17 inch depth $6,200 - $11,100 $6,200 - $11,100 24% Configuration #3: New equipment design...
-
Supporting Documents for the Medical Diagnostic Equipment Accessibility Standards Advisory Committee Report
Equipment Accessibility Standards Advisory Committee work were utilized in the Committee’s final report “Advancing Equal Access to Diagnostic Services: Recommendations on Standards for the Design...
-
§27.15(a)
The notification shall also include an identification of the responsible employee designated pursuant to §27.13(a)....
-
Toilet Compartments
To achieve compliance with TAS for both the toilet compartment and baby changing table, it may be necessary to design the toilet compartment to exceed the minimum size requirements of TAS...
-
A.2.ii. - Should EIT be compatible with assistive technology?
These products, such as information kiosks, copiers, or other similar products that do not permit a user to install or connect assistive technology, must be designed so that an end user...
-
Comments on the Costs of Implementation
In addition to the comments on the specific features of the three design options, one of the issues most widely commented upon was the cost of compliance with the Act's accessibility requirements...
-
A. Complaint Procedures and Complaints Resolution Officials (CRO’s)
Carriers must (i) establish a procedure for resolving disability-related complaints raised by passengers with a disability and (ii) designate at least one CRO to be available to handle disability-related...
-
If Passenger with a Disability Requests Private Screening
You must always seek assistance from the appropriate designated personnel in making such a decision....
-
11B-411.2.2.2 Verbal identification
When the accessibility function button is pressed, verbal announcement of the car designation shall be provided at the elevator car entrance upon arrival....
-
§35.130(b)(1)(iv) (Section-by-Section Analysis)
benefits, or services would be more effective, paragraph (b)(2) provides that a qualified individual with a disability still has the right to choose to participate in the program that is not designed...
-
"1991 Standards" and "2004 ADAAG" (Section-by-Section Analysis)
The term ‘‘1991 Standards'' refers to the ADA Standards for Accessible Design, originally published on July 26, 1991, and republished as Appendix D to 28 CFR part 36....
-
806.4 Hotel, Motel and Condominium Special Accessibility Features
(ii) All beds in designed accessible guest rooms shall be open-frame type that allows the passage of lift devices. (iii) Water closets that comply with section 604.4....
-
A1. Parking Count
aisle + 1 van-accessible space 51-75 2 spaces w/ min. 60 inch wide access aisle + 1 van-accessible space If more than 75, see the ADA Standards for Accessible Design...
-
C102.2 American National Standards Institute/ Human Factors and Ergonomics Society (ANSI/HFES)
ANSI/HFES 200.2 provides design specifications for human-system software interfaces to ensure that software is accessible to people with a wide range of physical, sensory, and cognitive...
-
Passenger Loading Zones [4.6.6]
Where zones are specifically designed for passenger loading and unloading, at least one on a site must be accessible....
-
Grade (R302.5) (Section-by-Section Analysis)
This is consistent with the AASHTO “Policy on Geometric Design of Highways and Streets” which recommends that the sidewalk grade follow the grade of adjacent roadways, and also recommends...