All operable parts, including coin slots, shall be 40 inches (1016 mm) maximum above the finish floor....
Search Results "Floor Designation"
-
11B-603.5 Accessories
-
407.12.3.1 Unobstructed Forward Reach (Section-by-Section Analysis)
Analysis) This section proposes that, where an unobstructed forward reach is provided, the operable part must be located 48 inches high maximum and 15 inches high minimum above the floor...
-
407.12.2.2 Obstructed Side Reach (Section-by-Section Analysis)
located more than 10 inches, but not more than 24 inches, behind the vertical reference plane, the height of the operable part must be 46 inches maximum and 15 inches minimum above the floor...
-
4.10.6* Door Protective and Reopening Device
device shall be capable of completing these operations without requiring contact for an obstruction passing through the opening at heights of 5 in and 29 in (125 mm and 735 mm) above finish floor...
-
Safety Considerations for Site Selection
When possible, request meeting rooms on the ground floor with direct accessible paths to the outside....
-
Slope [4.3.7]
Requirements in 4.3, while based on the expectation of level floors, apply equally to exterior sites....
-
4.10.6* DOOR PROTECTIVE AND REOPENING DEVICE
device shall be capable of completing these operations without requiring contact for an obstruction passing through the opening at heights of 5 in and 29 in (125 mm and 735 mm) from the floor...
-
11B-604.9.6 Dispensers
The outlet of the dispenser shall be 14 inches (356 mm) minimum and 19 inches (483 mm) maximum above the finish floor....
-
11B-602.9 Pedestrian protection
When used, wing walls or barriers shall project horizontally at least as far as the drinking fountain and to within 6 inches (152 mm) vertically from the floor or ground surface....
-
11B-809.7 Accessible routes
The accessible route shall adjoin or overlap clear floor spaces and connect all exterior doors....
-
904.4 Sales and Service Counters
of the number of existing mail boxes, the counter shall be permitted to have a portion which is 24 inches (610 mm) long minimum complying with 904.4.1 provided that the required clear floor...
-
610.2 Bathtub Seats
The top of bathtub seats shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the bathroom finish floor....
-
H.
Cinemark has also expressed its concern to the Department that ADA Standard 4.33.3 and the United States' interpretation thereof provided insufficient guidance for theater designers about...
-
Amusement rides
Section 234 of the 2010 Standards provides accessibility guidelines for newly designed and constructed amusement rides....
-
General
Like many other facilities designed to be accessible, accessible toilet facilities can and do serve a wide range of individuals with and without disabilities....
-
Fact Sheet: Highlights of the Final Rule to Amend the Department of Justice's Regulation Implementing Title III of the ADA
The ADA requires the Department to publish ADA design standards that are consistent with the minimum guidelines published by the U.S....
-
Public Rights-of-Way
These comments addressed roadway design, speed bumps, crosswalks, on-street parking, audible signs and pedestrian signals, and emergency call boxes....
-
11B-405.8 Handrails
[2010 ADAS] EXCEPTION: Within employee work areas, handrails shall not be required where ramps that are part of common use circulation paths are designed to permit the installation...
-
Accessible Gates for Trails and Roads
jgroenier@fs.fed.us Accessible Gates for Trails and Roads James "Scott" Groenier, Project Leader The Missoula Technology and Development Center (MTDC) has reviewed available gate designs...
-
"Existing Facility" (Section-by-Section Analysis)
Under the ADA, a facility is initially classified as one of three types: (1) An existing facility; (2) an altered facility; or (3) a newly designed and constructed facility. ...
-
C.3.i. - Does Section 508 require contractors to manufacture EIT that meets the applicable Access Board’s technical provisions?
By doing so, Section 508 provides an incentive for EIT manufacturers and designers to ensure that their products are usable by everyone – including people with disabilities....
-
Amusement rides. (Section-by-Section Analysis)
Section 234 of the 2010 Standards provides accessibility guidelines for newly designed and constructed amusement rides....
-
Size and Spacing of Grab Bars and Handrails [4.26.2]
Large sections, particularly those of rectangular design, are not as graspable as small circular sections. A gripping surface with a diameter between 1¼ to 1½ inches is specified....
-
Alterations: Alternate Stalls
Alternate designs in ADAAG Figure 30(b) allow narrower stall widths while requiring greater depth....