Step tread surfaces shall comply with T302....
Search Results "Surface Slope"
Commonly Searched Documents
- 
    
  
  T405.2 Surfaces
  
- 
    
  
  Dimensional Tolerances in Construction and for Surface Accessibility
  [See subsections ...] 
- 
    
  
  C1-6. Accessible Route Slope
  If the slope of part of the accessible route is greater than 1:20, does this part meet the following requirements for an accessible ramp? Yes _____ No _____... 
- 
    
  
  Running Slope [1018.7.1]
  The running slope of any segment of a beach access route must be no steeper than 1:10 (10 percent).... 
- 
    
  
  General: ADA Standard Section 505.1
  Section 505.1 of the ADA Standards covers information in the current ADA Standards for handrails. 
- 
    
  
  11B-505.1 General
  Handrails are not required on walking surfaces with running slopes less than 1:20.... 
- 
    
  
  Highway standards suggesting possible applications for pedestrian surfaces
  ASTM E 950-98(2004) Standard test method for measuring the longitudinal profile of traveled surfaces with an accelerometer established inertial profiling reference... 
- 
    
  
  R409.6 Gripping Surface
  R409.6 Gripping Surface. Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides.... 
- 
    
  
  Loose Fill Surfaces
  Loose Fill Surfaces. The predominant surface characteristic is one where many loose particles are combined to create the surface system. ... 
- 
    
  
  Performance for Surface Firmness and Stability
  Performance for Surface Firmness and Stability In addition to the visual inspection and calculation of the surface deficiency score, the firmness and stability of the surfaces were measured... 
- Figure 1009.3.2 Sloped Entry Submerged Depth – Drawing from the U.S. Access Board
- 
    
  
  11B-902.1 General
  Dining surfaces and work surfaces shall comply with Sections 11B-902.2 and 11B-902.3.... 
- 
    
  
  11B-505.6 Gripping surface
  The bottoms of handrail gripping surfaces shall not be obstructed for more than 20 percent of their length.... 
- 
    
  
  11B-809.9.4 Work surfaces
  Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches... 
- 
    
  
  Stability or Stable Surface
  Stability or Stable Surface. ... 
- 
    
  
  Ramps
  Slightly steeper running slopes are permitted for short ramps (maximum 6” rise) where space is limited (§405.2, Ex.).... 
- 
    
  
  13. Do the provisions for openings in floor and ground surfaces in Section 302.3 apply to walking surfaces in play areas?
  Do the provisions for openings in floor and ground surfaces in Section 302.3 apply to walking surfaces in play areas? Yes.... 
- 
    
  
  11B-302 FLOOR OR GROUND SURFACES
  [See subsections ...] 
- 
    
  
  Common Questions (Floor and Ground Surfaces)
  Common Questions 
- 
    
  
  11B-302 Floor or ground surfaces.
  [See subsections ...] 
- 
    
  
  11B-302 Floor or ground surfaces
  [See subsections ...] 
- 
    
  
  Vertical Surface Discontinuities
  Vertical Surface Discontinuities. Vertical differences in level between two adjacent surfaces.... 
- 
    
  
  407.4.2 Floor Surfaces
  407.4.2 Floor Surfaces. Floor surfaces in elevator cars shall comply with 302 and 303.... 
- 
    
  
  11B-505.6 Gripping surface
  The bottoms of handrail gripping surfaces shall not be obstructed for more than 20 percent of their length.... 
