[2010 ADAS] 608.3.2 Standard Roll-In Type Shower Compartments. ...
Search Results "Referenced Standard"
Filters
Commonly Searched Documents
-
11B-608.3.2 Standard roll-in type shower compartments
-
11B-608.3.2 Standard roll-in type shower compartments
[2010 ADAS] 608.3.2 Standard Roll-In Type Shower Compartments....
-
§ 1194.1 Standards for Section 508 of the Rehabilitation Act.
The standards for information and communication technology developed, procured, maintained, or used by Federal agencies covered by Section 508 of the Rehabilitation Act are set forth in...
-
ASA Standards Store
-
Subpart B -- Technical Standards (Formerly Subpart B -- Accessibility Standards in the NPRM) (Preamble, Section-by-Section Analysis)
Subpart B -- Technical Standards (Formerly Subpart B -- Accessibility Standards in the NPRM) (Preamble, Section-by-Section Analysis) Comment....
-
2) Where the Standard says "Changes in level are not permitted"
2) Where the Standard says "Changes in level are not permitted", such as 304.2 for turning spaces: Here the standard is followed by an unenforceable advisory that says, "As used in this...
-
3. Comparison of WCAG 2.0 to Existing 508 Standards
While the WCAG 2.0 Success Criteria build on the heritage of the existing 508 Standards, they are generally more explicit than the standards....
-
SECTION 202 DEFINITIONS
Editor's Note Where ADA definitions for specific terms differ notably from CBC, the ADA definition is inserted below the CBC definition and identified by green text and headed by [2010 ADA Standards...
-
General: ADA Standard Section 207.1
Section 207.1 of the ADA Standards covers information on scoping requirements for accessible means of egress in the most current ADA Standards.
-
C102.1 Incorporation by Reference
Where conflicts occur between the 255 Guidelines and the referenced standards, these guidelines apply....
-
Standards that exclude an entire class of individuals with disabilities
Standards that exclude an entire class of individuals with disabilities "Blanket" exclusions of this kind usually have been established because employers believed them to be necessary...
-
11B-207.2 Platform lifts
[2010 ADA Standards] 207.2 Platform Lifts....
-
Guidance on the 2010 ADA Standards for Accessible Design
Guidance on the 2010 ADA Standards for Accessible Design Reproduction of this document is encouraged....
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
Definitions [§106]
Definitions [§106] Many important terms used in the ADA Standards are defined in section 106....
-
608.2.2 Standard Roll-In Type Shower Compartments
Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
Reason the Access Board is issuing the proposed standards
Section 510 of the Rehabilitation Act (29 USC 794f) requires the Access Board, in consultation with the Commissioner of the Food and Drug Administration, to issue standards that contain...
-
ABA Accessibility Standard for GSA Facilities Pocket Guide
Pocket Guide to the ABA Accessibility Standard for GSA Facilities With Selected Sections from GSA’s Federal Management Regulation Final Rule Adopting GSA’s ABA Accessibility Standard...
-
404.3 Automatic and Power-Assisted Doors and Gates
Full-powered automatic doors shall comply with ANSI/BHMA A156.10 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
1) Where the Standard specifically refers to 303
1) Where the Standard specifically refers to 303, such as 403.4 changes in level for walking surfaces: Here it is clear that changes in level that comply with either the ¼" maximum vertical...
-
§1630.10(b) Qualification standards and tests related to uncorrected vision
(b) Qualification standards and tests related to uncorrected vision....
-
2010 ADA Standards
104.1.1 Construction and Manufacturing Tolerances. All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific...
-
1991 ADA Standards
3.2 Dimensional Tolerances. All dimensions are subject to conventional building industry tolerances for field conditions.
-
Proposed training standards.
The Department has always required that service animals be individually trained to do work or perform tasks for the benefit of an individual with a disability, but has never imposed...