RECOMMENDATIONS An objective test procedure for measuring the firmness and stability of surfaces with a portable device and performance specifications need to be accepted in order to...
Search Results "Measuring Instrument"
-
RECOMMENDATIONS
-
6.9 Tread Obstacles
Obstacles on beach access routes and their related resting intervals shall not exceed 1 inch (25 mm) in height measured vertically to the highest point....
-
Fuel Gas Conditioning Systems for Clean and Reliable Gas Supply by EN-FAB Inc
After the gas is cleaned it is usually measured, and the pressure reduced....
-
Performance for Surface Firmness and Stability
The baseline measurements affirmed the RP was operable and calibrated....
-
11B-608.2.1 Transfer type shower compartments
Transfer type shower compartments shall be 36 inches (914 mm) by 36 inches (914 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (914...
-
Appendix: Revised Annotated Bibliography
The instrument was of optimum accuracy ("5Fm), ing the rapid measurement of maximum arm reach to 231 positions in space around each subject, while its repeat accuracy was 2.5Fm....
-
2. Analysis of footrest clearance height and depth
Front castor and footrest measurements were available for 67 power wheelchair users (excluding front-wheel drives for this analysis, due to time constraints)....
-
Issue 4: Based on available references, can we develop “viable” design standards and guidelines”?
Must they be written in terms of measurable parameters and values? Consensus was not obvious. Must they be written in terms of measurable parameters and values?...
-
§104.42(b)(3)(i)
handicap that impairs sensory, manual, or speaking skills, the test results accurately reflect the applicant's aptitude or achievement level or whatever other factor the test purports to measure...
-
§ 36.309(b)(1)(i)
impairs sensory, manual, or speaking skills, the examination results accurately reflect the individual´s aptitude or achievement level or whatever other factor the examination purports to measure...
-
RESEARCH OBJECTIVES
Objectively measure the firmness and stability of the test surfaces; 3....
-
Double Action Door Pressure Gauge
Double Action Door Pressure Gauge This Door Pressure Gauge, available from Evan Terry Associates, has Push-Pull capability and measures forces from 0-35 pounds on one side and 0-16...
-
AVAILABLE DATA DO NOT SUPPORT DEPARTING FROM THE CURRENTLY ACCEPTED STANDARD OF 19-INCH TRANSFER SURFACE HEIGHT
There is a recognized international standard defining various measurements of wheelchairs: ISO 7176-7:1998 Wheelchairs — Part 7: Measurement of seating and wheel dimensions....
-
How to Use this Checklist
One person can take measurements and the other person can fill out the checklist and take photos....
-
C. Training
As part of its training program for election officials and poll workers, the County will provide training concerning temporary remedial measures, including: (a) why such measures are necessary...
-
11B-306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
11B-306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
Low Vision and Blindness
And when ophthalmologists measure your vision, they measure visual acuity. And visual acuity is expressed as a ratio of 20/20, 20/200....
-
§8.12(b)
that impairs sensory, manual, or speaking skills, the test results accurately reflect the applicant's or employee's job skills, aptitude, or whatever other factor the test purports to measure...
-
11B-405.3 Cross slope
Cross slope is measured the same way as slope is measured (i.e., the rise over the run). Advisory 11B-405.3 Cross slope....
-
C102.8.2 TIA 1083
Telephone Terminal Equipment Handset Magnetic Measurement Procedures and Performance Requirements, (March 2007), IBR proposed for Section 410.4.2....
-
1018.5 Obstacles
This section requires obstacles to not exceed 1/2 inch in height measured vertically to the highest point....
-
4.34.6.5(1)
(1) The sink and surrounding counter shall be mounted at a maximum height of 34 in (865 mm) above the floor, measured from the floor to the top of the counter surface, or shall be adjustable...
-
11B-405.3 Cross slope
Cross slope is measured the same way as slope is measured (i.e., the rise over the run). Advisory 11B-405.3 Cross slope....