Handrails shall be continuous within the full length of each stair flight or ramp run....
Search Results "Handrail Clearance"
-
505.3 Continuity
-
Range or Cooktop: ADA Standard Section 804.6.4
Where a forward approach is provided, the clear floor or ground space shall provide knee and toe clearance complying with 306....
-
11B-804.6.4 Range or cooktop
Where a forward approach is provided, the clear floor or ground space shall provide knee and toe clearance complying with Section 11B-306....
-
11B-804.6.4 Range or cooktop
Where a forward approach is provided, the clear floor or ground space shall provide knee and toe clearance complying with Section 11B-306....
-
505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
Accessible Ramp Features
At least 36 inches between handrails 2. Top landing part of walk 3. Bottom landing part of walk 4. Handrail height 34 to 38 inches 5. Edge protection...
-
Assembly Areas
Because handrails may interfere with egress where they adjoin seating and since accessible routes are required to connect to wheelchair seating locations, compliance with 4.9, including...
-
R409.7 Cross Section
Handrail gripping surfaces shall have a cross section complying with R409.7.1 or R409.7.2....
-
Figure 404.2.4.1(e) Maneuvering Clearances at Manual Swinging Doors and Gates: Hinge Approach, Pull Side – Drawing from the U.S. Access Board
-
Figure 404.2.4.1(f) Maneuvering Clearances at Manual Swinging Doors and Gates: Hinge Approach, Push Side – Drawing from the U.S. Access Board
-
Figure 404.2.4.1(h) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Pull Side – Drawing from the U.S. Access Board
-
Figure 404.2.4.1(j) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Push Side – Drawing from the U.S. Access Board
-
Figure 404.2.4.1(d) Maneuvering Clearances at Manual Swinging Doors and Gates: Hinge Approach, Pull Side – Drawing from the U.S. Access Board
-
4.15.5 Clearances.
[See subsections ...]
-
4.15.5 CLEARANCES
[See subsections ...]
-
6.12 Handrails and Edge Protection
Where elevated dune crossings or dune crossings steeper than 1:20 (5 percent) are part of beach access routes, handrails complying with ABAAS section 505 and edge protection complying...
-
Figure 404.2.4.1(i) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Pull Side with Closer – Drawing from the U.S. Access Board
-
Door Maneuvering Clearance
Section 404.2.4 addresses maneuvering clearances at manual doors, doorways, and gates....
-
Vertical Clearance
A minimum vertical clearance of 114 inches is required at passenger loading zones and along at least one vehicular route connecting accessible loading zones with site entrance and exits....
-
Figure 404.2.4.1(g) Maneuvering Clearances at Manual Swinging Doors and Gates: Hinge Approach, Push Side with Closer and Latch – Drawing from the U.S. Access Board
-
T303 Handrails, Stanchions, and Handholds
[See subsections ...]
-
T207 Handrails, Stanchions, and Handholds
[See subsections ...]
-
d-ii
Are handrails installed on both sides of each ramp segment? [ADA Standards § 4.8.5] Yes No...
-
f-ii
Are handrails installed on both sides of each ramp segment? [ADA Standards § 4.8.5] Yes No...
