COMPACT DESIGN AND INTEGRATED COMPONENTS PROVIDE: Greater architectural design freedom Space-saving configuration for more rentable space Less moving parts for greater durability...
Search Results "Clear Floor Space"
Filters
Commonly Searched Documents
-
Otis Gen2 Elevator
-
Whitehall Mfg. Single Temp Piezo Widespread Pushbutton Electronic Valve Conical Faucet
As loose components, the spout and pushbutton may be installed with any centerset spacing, however, 4", 6" or 8" centersets are suggested....
-
Whitehall Mfg. Single Temp Sensor Activated Widespread Electronic Valve Conical Faucet
As loose components, the spout and pushbutton may be installed with any centerset spacing, however, 4, 6 or 8 inch centersets are suggested....
-
Angled (Front-In) Parking
ADAAG's requirement for an access aisle on either side of a space (they can be shared by two spaces) is based on the assumption that drivers can head in or back in as needed....
-
F202.3 Alterations
The final rule adds Exception 4 to this section, which applies to altered elements and spaces....
-
Section 4.1.2, Accessible Sites and Exterior Facilities: New Construction (Section-By-Section Analysis and Response to Comments)
Interior elements and spaces are covered by Sec.4.1.3....
-
Problem Four
Problem Four: No sign with the international symbol of accessibility is installed at each accessible parking space....
-
11B-703.5.5 Character height
Exception: Where provided, floor plans providing emergency procedures information in accordance with Title 19 shall not be required to comply with Section 11B-703.5.5....
-
11B-608.6 Shower spray unit and water
One shower head shall be located at a height of 48 inches (1219 mm) maximum above the shower finish floor....
-
Parking
Parking The chart below indicates the number of accessible spaces required by the 2010 Standards. One out of every six accessible spaces must be van-accessible....
-
11B-409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (12.7 mm) under rated loading to zero loading conditions....
-
407.4.6.2 Buttons
Car control buttons with floor designations shall comply with 407.4.6.2 and shall be raised or flush. EXCEPTION: In existing elevators, buttons shall be permitted to be recessed....
-
902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (760 mm) maximum above the finish floor or ground....
-
409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (13 mm) under rated loading to zero loading conditions....
-
2. Rear grab bar
Rear grab bar: There is a grab bar behind the toilet that is at least 36 inches long and from 33 to 36 inches above the floor....
-
407.4.6.2 Buttons
Car control buttons with floor designations shall comply with 407.4.6.2 and shall be raised or flush. EXCEPTION: In existing elevators, buttons shall be permitted to be recessed....
-
902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (760 mm) maximum above the finish floor or ground....
-
904.5.2 Tray Slides
The tops of tray slides shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground....
-
6. Toilet Seat
Is the toilet seat in each accessible toilet room between 17"-19" above the floor? [ADA Stds. 4.16.3] Yes __ No __ N/A __ Comments: _____________________________________...
-
H28
Is the surface of the toilet seat in this 36-inch-wide stall 17 to 19 inches above the floor? [ADA Standards §§ 4.16.3; 4.22.4] Yes No...
-
11B-902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (762 mm) maximum above the finish floor or ground....
-
11B-904.5.2 Tray slides
The tops of tray slides shall be 28 inches (711 mm) minimum and 34 inches (864 mm) maximum above the finish floor or ground....
-
6e.
Are the controls and operating mechanisms mounted no more than 54 inches above the floor for a side reach or 48 inches for a forward reach? Yes _____ No _____...
-
4.19.6* Mirrors
Mirrors shall be mounted with the bottom edge of the reflecting surface no higher than 40 in (1015 mm) above the finish floor (see Fig. 31)....
