The Fair Housing Act requires that covered multifamily dwellings for first occupancy after March 13, 1991 be designed and constructed in accordance with the Act's accessibility requirements...
Search Results "Designated Aisle Seat (Assembly)"
Filters
Commonly Searched Documents
-
Scope of Coverage
-
Amusement rides. (Section-by-Section Analysis)
Section 234 of the 2010 Standards provides accessibility guidelines for newly designed and constructed amusement rides....
-
Size and Spacing of Grab Bars and Handrails [4.26.2]
Large sections, particularly those of rectangular design, are not as graspable as small circular sections. A gripping surface with a diameter between 1¼ to 1½ inches is specified....
-
Alterations: Alternate Stalls
Alternate designs in ADAAG Figure 30(b) allow narrower stall widths while requiring greater depth....
-
217 Telephones
1991 Standards for Accessible Design 2010 Standards for Accessible Design What’s New/Different 4.1.3(17)(b) All telephones...
-
211 Drinking Fountains
1991 Standards for Accessible Design 2010 Standards for Accessible Design What’s New/Different 4.1.3(10)(a) Where...
-
I. Definitions
“Accessible on Election Day” means that a polling place is compliant with the 2010 ADA Standards for Accessible Design (“2010 Standards”) (28 C.F.R. § 35.104, as set forth in appendices...
-
1193.23(b)(3) (Advisory Guidance)
Working cooperatively with appropriate disability-related organizations is one of the factors that manufacturers must consider in their product design and development process....
-
12204(c)(3) Other sites
.-- With respect to alterations of buildings or facilities designated as historic under State or local law, the guidelines described in paragraph (1) shall establish procedures equivalent...
-
1.6.10 Fixed Route System.
A system of transporting individuals (other than by aircraft), including the provision of designated public transportation service by public entities and the provision of transportation...
-
3001.1 Scope
This chapter governs the design, construction, installation, alteration and repair of elevators and conveying systems and their components....
-
New Construction and Alterations
New Construction and Alterations Businesses whose facilities were built or altered since the ADA went into effect must comply with the ADA Standards for Accessible Design so that the...
-
[F] 907.5.2.3.2 Employee work areas
Where employee work areas have audible alarm coverage, the notification appliance circuits serving the employee work areas shall be initially designed with a minimum of 20-percent spare...
-
1007.6.2 Separation
Each area of refuge shall be designed to minimize the intrusion of smoke....
-
243 Shooting Facilities with Firing Positions
Facilities with Firing Positions Sections 243 and 1010 of the 2010 Standards require an accessible turning space for each different type of firing position at a shooting facility if designed...
-
GSA
General Services Administration, acting by or through the Administrator of General Services, or a designated official to whom functions under this part have been delegated by the Administrator...
-
Use Zone
Use Zone - The ground level area beneath and immediately adjacent to a play structure or piece of equipment that is designated by ASTM F 1487 Standard Consumer Safety Performance Specification...
-
12183(a)(1)
(1) a failure to design and construct facilities for first occupancy later than 30 months after July 26, 1990, that are readily accessible to and usable by individuals with disabilities,...
-
12204(c)(3) Other sites
(3) Other sites With respect to alterations of buildings or facilities designated as historic under State or local law, the guidelines described in paragraph (1) shall establish procedures...
-
The Facilities Toolbox
The "Facilities Toolbox" is an interactive Forest Service facility management Web site designed to help line officers and their staffs manage facilities effectively....
-
4.1.3(14)
Emergency warning systems in medical care facilities may be modified to suit standard health care alarm design practice....
-
A4.10.6 Door Protective and Reopening Device
However, if designed in accordance with ASME A17.1‒1990, the door closing movement could still be stopped if a person or object exerts sufficient force at any point on the door edge....
-
R103.1 Conventional Industry Tolerances
Conventional industry tolerances do not apply to design work....
-
§100.205(e)(2)(vi) 2006 International Building Code
2007, erratum to correct the text missing from Section 1107.7.5, if adopted without modification and without waiver of any of the provisions intended to address the Fair Housing Act's design...